- Home
- Knowledge
Knowledge · 17 guides
Screen printing guides for buyers and production engineers
Short, plain answers to the questions Sunstar is asked most: which machine to buy, and how to fix a print that is not coming out right.
Choosing a machine
Comparisons and buying guides.
Flatbed vs cylinder screen printing machine
Choose a flatbed if you print rigid or thick material, or mixed jobs in short and medium runs at around 500 sheets an hour. Choose a stop-cylinder press if you print thin flexible sheets in long runs and need 1,800 to 4,000 sheets an hour. Many plants run both.
Read →GuideSemi-automatic vs fully automatic screen printing machine
A semi-automatic screen printing machine prints by itself, but an operator loads and removes each sheet. A fully automatic machine also feeds, registers and delivers the sheet to the dryer. Semi-automatic suits short runs and many job changes. Fully automatic suits steady volume, where output and consistency repay the higher cost.
Read →GuideHow to choose an industrial screen printing machine
Five facts about your job decide the machine: the material and its thickness, the print size, the output you need per hour, the register tolerance and the ink. With these in hand, the choice between a flatbed, a cylinder press, a roll-to-roll press or a purpose-built printer is usually clear.
Read →GuideImported vs Indian screen printing machine
A lower-cost Indian-made screen printing machine is a sensible choice for simple graphics, wide tolerances, short runs and a tight budget. A precision imported press earns its cost on multi-layer and functional work, tight register and high volume, where rejects are expensive. The tolerance of your part and the cost of a rejected sheet decide it.
Read →GuideScreen printing vs digital printing for industrial parts
Screen printing is the better process for volume production, for thick or opaque ink films and for functional inks such as silver, carbon and glass enamel. Digital printing is better for short runs, many design versions and variable data. It is common to use digital for samples and screen printing for production.
Read →GuideHow membrane switches are made
A membrane switch is made by screen printing a graphic overlay and one or two circuit layers on plastic film, then cutting them and laminating them with a spacer and adhesive. The circuit is printed in silver and carbon ink, with a dielectric layer for insulation. Each printed layer is dried or cured before the next, and each has to register to the others.
Read →GuideHow glucose test strips are screen printed
A glucose test strip is made by screen printing carbon and silver electrodes on plastic film, printing an insulation layer that leaves a small electrode area open, and adding the enzyme reagent. Many strips are printed side by side on one sheet or along a reel, then covered and cut apart. The electrode area sets the reading, so line width, ink deposit and register are held tightly.
Read →GuideFine-line screen printing on polycarbonate
Fine lines on polycarbonate need four things to be right together: a fine mesh at high tension, a thin and flat stencil with a sharp image, a sharp squeegee at low pressure, and a clean, flat sheet free of static. Lines of around 100 to 150 microns are typically achievable on a well set flatbed press. Finer lines need closer control of every step.
Read →On the shop floor
Settings, problems and fixes.
Screen tension in N/cm
Screen tension is the pulling force in the stretched mesh, measured in newtons per centimetre (N/cm) with a tension meter resting on the mesh. Most polyester screens for industrial work run at about 16 to 30 N/cm. The right figure depends on the mesh count and thread diameter, and the mesh maker's data sheet gives it for each mesh.
Read →GuideOff-contact and snap-off
Off-contact distance, also called snap-off, is the gap between the underside of the screen and the substrate before the squeegee presses the mesh down. On a well-tensioned screen it is typically 1 to 3 mm for small frames and 3 to 8 mm for large frames. Use the smallest gap that lets the mesh lift cleanly behind the squeegee.
Read →GuideSqueegee pressure, angle and hardness
Squeegee pressure, angle and hardness together decide how much ink passes through the screen and how sharp the printed edge is. Use the lowest pressure that gives a complete print, an angle of about 70 to 75 degrees as a starting point, and a blade of 70 to 75 Shore A for general work. A softer blade, a flatter angle and a slower stroke all put down more ink.
Read →GuideRegistration problems in multicolour printing
Registration problems in multicolour screen printing come from four places: the screens, the substrate, the press and the artwork. Look at how the error behaves before changing anything. A constant error is a setup fault. A random error is a feeding fault. An error that grows across the sheet is a change of size in the screen or the substrate.
Read →GuideUV ink not curing
UV ink that stays tacky, scratches off or fails a tape test has usually received too little UV energy for its film thickness and colour. Measure the UV dose on the belt with a radiometer, in mJ/cm², and compare it with the figure in the ink maker's data sheet. The common causes are an aged lamp, dirty reflectors, a belt running too fast and an ink film that is too thick.
Read →GuideMesh count for conductive ink
For silver and carbon conductive pastes on membrane switches and printed sensors, polyester mesh of about 61 to 90 threads per cm is typical. Finer tracks use polyester of 120 threads per cm or more, or stainless steel mesh of 325 to 400 threads per inch. Start with the mesh named in the paste maker's data sheet, because particle size and target resistance decide the choice.
Read →GuideEmulsion thickness (EOM)
EOM, or emulsion over mesh, is the thickness of emulsion that stands beyond the mesh on the print side of the screen. For fine lines and halftones it is typically 3 to 8 microns, or about 10 to 20 percent of the mesh thickness. EOM is set by how the screen is coated: the number of coats, the side they are applied from, the coating speed and the trough.
Read →GuideCTS vs film positives
With film positives, the artwork is output on film, laid on the coated screen in a vacuum frame and exposed. Computer to screen (CTS) writes the artwork onto the coated screen with UV light, straight from the file. CTS removes the film, the vacuum frame and manual positioning. Film remains workable for a screen room that makes only a few simple screens a week.
Read →GuideScreen printing defects
Most screen printing defects come from the screen, the squeegee, the ink or the off-contact setting. The table below gives the usual cause and fix for pinholes, sawtooth edges, bleeding, smudging, moiré and uneven deposit. Change one setting at a time and keep a record of what worked.
Read →Words and terms
Glossary
108 screen printing terms explained in a line or two each, from off-contact to EOM.
Open → ReferenceWhich printing machine do I need
Common search terms, what each one means and whether Sunstar supplies a machine for it.
Open → ReferencePrice guide
How the price of each machine class is set, what moves it and what to send for a quotation.
Open →Inquiry
Tell Sunstar what you print.
An engineer replies within one working day with machine options and Indian pricing. Delivered and installed anywhere in India.
