- Home
- Process
Process · 3 stages
The screen printing process, step by step
A print line has three stages: making the screen, printing, and curing. Sunstar supplies the machines for all three.
Pre-press
Print quality starts with the screen.
- Stretch
- Coat
- Image
- Develop and wash
- Dry
- Reclaim
Printing
The press holds the substrate, brings the screen down and drives the squeegee.
- Flatbed
- Cylinder
- Roll-to-roll
- Glass, PCB and parts
- Squeegees
Curing
After the press, the ink has to be dried or cured before sheets are stacked or printed again.
- IR and hot air
- UV curing
- IR + UV
- Converting
How a print is made
Six steps, six machines. The clips are illustrations of each step, generated with AI. They are not footage of a specific machine.
The six steps in words
And the machine Sunstar supplies for each.
- Stretch the mesh
Polyester mesh is pulled to a set tension and glued to the frame. Even tension keeps register on every print after this.
- Coat the emulsion
A trough of light-sensitive emulsion is drawn up the mesh in one pass, to an exact thickness.
- Image the stencil
A UV head writes the artwork straight onto the emulsion, without film. Where light hits, the emulsion hardens. The rest washes out.
- Print the sheet
The screen drops to a few millimetres above the sheet. The squeegee presses the mesh down and pushes ink through. The flood bar then refills the mesh, and the screen lifts.
- Cure in line
The sheet rides a conveyor under infrared or UV lamps. It leaves the tunnel dry and ready to stack.
- Cut to size
For reel work, the printed web is registered by camera and cut to sheets, ready to ship.
Machine types by stage
Fully automatic flatbeds, cylinder presses and reel-fed printers
An automatic screen printing machine feeds the sheet, registers it, prints it and delivers it to the dryer without an operator handling each piece.
See models →Machine typeOperator-fed electric flatbeds and precision part printers
A semi-automatic screen printing machine prints each sheet by motor while an operator loads and unloads it.
See models →Machine typeFlat bed presses for rigid and flexible sheets up to 25 mm thick
A flatbed screen printing machine holds the sheet flat on a vacuum bed.
See models →Machine typeSPS presses for flexible sheets at up to 4,000 sheets an hour
A stop-cylinder screen printing press grips a flexible sheet on a cylinder.
See models →Machine typeReel to reel printers with camera registration and in-line curing
A roll-to-roll screen printing machine prints a continuous web of film or label stock from one reel to another.
See models →Machine typeCamera-aligned presses for fine lines and multilayer printing
A CCD registration screen printing machine uses cameras to find register marks on the sheet or web before each print.
See models →Machine typeFeeder, press, dryer and stacker specified together as one line
An automatic screen printing line joins the machines around the press so that sheets move through without being carried by hand.
See models →Machine typePneumatic mesh stretching to a set, repeatable tension
A screen stretching machine pulls the mesh to a set tension in both directions and holds it while the mesh is glued to the frame.
See models →Machine typeAutomatic emulsion coating to the same thickness on every screen
A screen coating machine applies photo emulsion to the stretched mesh.
See models →By category: printers, pre-press, dryers, handling, squeegees.
Guides
Settings and fixes for each stage.
All guides →Screen tension in N/cm
Screen tension is the pulling force in the stretched mesh, measured in newtons per centimetre (N/cm) with a tension meter resting on the mesh. Most polyester screens for industrial work run at about 16 to 30 N/cm. The right figure depends on the mesh count and thread diameter, and the mesh maker's data sheet gives it for each mesh.
Read →GuideOff-contact and snap-off
Off-contact distance, also called snap-off, is the gap between the underside of the screen and the substrate before the squeegee presses the mesh down. On a well-tensioned screen it is typically 1 to 3 mm for small frames and 3 to 8 mm for large frames. Use the smallest gap that lets the mesh lift cleanly behind the squeegee.
Read →GuideSqueegee pressure, angle and hardness
Squeegee pressure, angle and hardness together decide how much ink passes through the screen and how sharp the printed edge is. Use the lowest pressure that gives a complete print, an angle of about 70 to 75 degrees as a starting point, and a blade of 70 to 75 Shore A for general work. A softer blade, a flatter angle and a slower stroke all put down more ink.
Read →GuideRegistration problems in multicolour printing
Registration problems in multicolour screen printing come from four places: the screens, the substrate, the press and the artwork. Look at how the error behaves before changing anything. A constant error is a setup fault. A random error is a feeding fault. An error that grows across the sheet is a change of size in the screen or the substrate.
Read →GuideUV ink not curing
UV ink that stays tacky, scratches off or fails a tape test has usually received too little UV energy for its film thickness and colour. Measure the UV dose on the belt with a radiometer, in mJ/cm², and compare it with the figure in the ink maker's data sheet. The common causes are an aged lamp, dirty reflectors, a belt running too fast and an ink film that is too thick.
Read →GuideMesh count for conductive ink
For silver and carbon conductive pastes on membrane switches and printed sensors, polyester mesh of about 61 to 90 threads per cm is typical. Finer tracks use polyester of 120 threads per cm or more, or stainless steel mesh of 325 to 400 threads per inch. Start with the mesh named in the paste maker's data sheet, because particle size and target resistance decide the choice.
Read →Questions buyers ask
Why automate screen making?
Tension, coating thickness and washout decide print quality. Automatic machines make every screen the same.
Does Sunstar supply the full screen room?
Yes. Stretching, coating, imaging, washing, drying and reclaiming, specified together.
Does Sunstar install and service this machine in India?
Yes. Sunstar engineers install the machine, train your operators on site and handle service and spares from Mumbai.
What can a flatbed screen printer print on?
Rigid and flexible sheets: polycarbonate, polyester, PVC, glass, metal and board, up to 25 mm thick.
IR or UV dryer?
IR and hot air for solvent, water-based and plastisol inks. UV for UV inks.
How is a dryer sized?
By the width of the sheet and the speed of the press, so the ink is cured at full output.
Inquiry
Tell Sunstar what you print.
An engineer replies within one working day with machine options and Indian pricing. Delivered and installed anywhere in India.
