Skip to content
Sunstar Graphics Brochures

Glossary

Squeegee terms, A to Z

35 terms used on the squeegee pages, each with the words printers also use for it. The general screen printing glossary covers presses, screens, inks and dryers.

Adapter strip also: aluminium shim, insert bar, spacer strip
A strip placed in a standard holder so that a thinner RKS stabilised blade clamps in it. On Gallus rotary units a 10 x 4 mm spacer is supplied with RS WP blades. More →
Bevel also: bevelled edge, chamfer, slanted edge, PK profile
One face of the blade ground at an angle, usually with a small flat land at the tip. Gives a heavier, even deposit. RKS Carbon BW has a 45 degree chamfer with a 0.5 to 4 mm land; Carbon HT PK is ground at 30, 45 or 60 degrees. More →
Carbon fibre backing also: carbon carrier, CRP, carbon squeegee, carbon-backed blade
A carbon-fibre reinforced plastic sheet, 0.8 to 2.5 mm thick, that carries the polyurethane edge on RKS Carbon S, Carbon BW, Carbon HT PK and RS WP blades. Stiffer than glass fibre, so the blade can be thinner, and from 1.7 mm it carries static away through the machine earthing. More →
Colour code also: colour-coded blade, hardness colour
A colour on the strip or printing edge that shows the Shore hardness on the press. On RKS Printan, red is 65, green 75, blue 85 and white 90 Shore A. More →
Diamond squeegee also: diamond blade, rhombic squeegee, Printan Diamond
A square polyurethane strip, 9.5 x 9.5 mm or 9.65 x 9.65 mm, held on its diagonal so a corner prints. Used in some solar and microelectronics print heads. More →
Double bevel also: V edge, PV profile, double-sided bevel
Both faces ground so the blade comes to a point or a narrow flat. Prints the same in both directions. More →
Dual-durometer blade also: Biflex, two-layer squeegee, double-durometer
A strip with a soft printing face backed by a 95 Shore A layer that stiffens the blade. RKS Printan Biflex is 65/95 or 75/95. More →
Durometer also: hardness, Shore hardness
The hardness of the blade material, measured on the Shore A scale. Also the name of the instrument that measures it. More →
Edge profile also: squeegee profile, blade profile, edge shape
The shape of the printing edge: square, single bevel, double bevel or V, rounded, or diamond. A square edge gives the thinnest, sharpest deposit; a rounded edge the heaviest. More →
EOM also: emulsion over mesh, stencil thickness
The thickness of the emulsion stencil above the mesh, which sets the ink film thickness together with the mesh and the squeegee. A thick EOM needs a blade that can fill it.
Flood bar also: flood blade, flood coater, return blade
The bar that spreads ink over the screen before the print stroke without pushing it through the mesh. The squeegee follows and prints. More →
Free height also: blade extension, exposed blade height
The part of the blade that sticks out of the holder. A longer free height flexes more and acts softer; a shorter one acts harder. More →
Glass fibre carrier also: GRP, GFK, fibreglass spine
The glass-fibre reinforced plastic carrier of the RKS System squeegee and RS rotary blade, about 0.8 to 2.5 mm thick. More →
Light gap test also: straight-edge test, plane-parallel check
Holding the blade edge against a straight edge in front of a light to see whether any daylight shows. A worn or wavy edge shows gaps; a freshly ground edge shows none. More →
Off-contact also: off-contact distance, off contact gap
The gap between the underside of the screen and the material before the squeegee presses the mesh down. It lets the mesh snap off behind the blade. More →
Polyurethane also: PU, squeegee rubber
The material nearly all squeegee blades are made of. Tough and wear-resistant, but it swells and softens when solvents soak in, which is why blades are rested and reground. More →
The pass of the squeegee across the screen that pushes ink through the stencil onto the material. Its speed, angle and pressure set the deposit. More →
RKS HT polyurethane also: HT material, HT1, HT3, HT edge
RKS's own polyurethane for UV and solvent inks and for pastes. HT1 is the single-layer strip, HT3 the triple-layer strip, and the HT edge is also used on Carbon BW, Carbon HT PK and colour-coded rotary blades. More →
RKS System squeegee also: System blade, Type 00, Type 32
The original RKS two-component blade: a glass-fibre carrier bonded to a 13 mm Vulkollan strip. Type 00 has a continuous carrier; Type 32 tapers towards the edge. More →
Rotary squeegee also: rotary blade, RS, RS WP, narrow-web squeegee
A thin, flexible stabilised blade for rotary screen units on label presses, with a 0.8 mm carrier and a rounded edge of 1.5, 2 or 3 mm. RKS RS has a glass-fibre carrier, RS WP a carbon carrier. More →
Rounded edge also: radius edge, PR profile, curved edge, small radius SR, large radius LR
A printing edge ground to a curve. Gives the heaviest deposit, for textured surfaces, Braille and textiles. RKS rotary blades are ordered with a small or large radius. More →
Sharpening angle also: grinding angle, chamfer grinding, regrind angle
The angle at which the grinder restores the edge. RKS System blades are ground at 92 degrees plus or minus 1 degree; RKS SM grinders set 0 or 2 degrees automatically and can grind a chamfer as an option. More →
Shore A also: Shore (DIN A), Sh A, degrees Shore
The hardness scale used for squeegee blades, from about 55 (soft) to 95 (very hard). 65 to 75 Shore A is the usual range for general graphic work; 75 to 85 for fine lines. More →
Single-durometer blade also: mono layer, Monoflex, single-layer squeegee
A blade with one hardness through the whole strip, such as RKS HT1 or Printan Monoflex. The standard conventional squeegee. More →
Snap-off also: peel, screen release
The mesh lifting away from the printed material immediately behind the squeegee, which leaves the ink on the material and keeps the print sharp. More →
Square edge also: flat edge, PO profile, 90 degree edge
The standard profile: the strip cut square so the edge is a sharp corner. Used for fine lines, text and most graphic work. More →
Squeegee also: squeegee blade, squeegee rubber, printing blade
The blade drawn across the screen to push ink through the mesh onto the material. Usually polyurethane, clamped in a holder on the print head. More →
Squeegee angle also: blade angle, print angle, attack angle
The angle between the blade and the screen during the stroke, typically 60 to 80 degrees. A more upright blade deposits less ink; a flatter blade deposits more. More →
Squeegee blade also: blade, strip
The replaceable strip that touches the screen, as distinct from the holder that clamps it. Sold by height, thickness, hardness, length and edge profile. More →
Squeegee holder also: holder, squeegee bar, clamp bar
The aluminium bar that clamps the blade and mounts on the print head. RKS Type U and Type S holders clamp pneumatically; Type S also swivels for blade changes. More →
Squeegee pressure also: print pressure, blade pressure
The force pressing the blade onto the screen. Use the lowest pressure that prints the full image; extra pressure bends the blade, widens lines and wears the stencil. More →
Squeegee sharpener also: squeegee grinder, grinding machine, blade grinder
A machine that grinds a worn blade back to a flat, parallel edge. RKS SM 600 TT and 1200 TT grinders have an automatic feed and a grinding head set by hand; the RKS SM series goes up to a fully automatic version with laser positioning. ATMA makes the ATS 100 / 150 and ATS 100D. More →
Stabilised squeegee also: two-component squeegee, composite blade, system squeegee
A thin polyurethane printing edge bonded to a rigid glass-fibre or carbon-fibre carrier, so the blade keeps its angle and stays parallel to the screen through the run. RKS System, Carbon and Rotary blades are of this type. More →
Triple-durometer blade also: sandwich blade, Triflex, three-layer squeegee, HT3
A strip with a hard core between two softer outer layers, such as RKS HT3 at 65/90/65, 75/90/75 or 85/90/85 Shore A. The core resists bending while the soft face seals against the screen. More →
Vulkollan also: VU
A polyurethane grade made without softeners, with good solvent and abrasion resistance. RKS uses it for the edge of System, Carbon S and RS rotary blades. More →

The general screen printing glossary →    Back to squeegees →

Inquiry

Ask for a blade.

Send the ink, mesh count, material and press model. Sunstar suggests a blade and quotes within one working day.

0 machines