---
title: How to Choose a Squeegee Blade for Screen Printing Ink
url: https://www.sunstargraphics.com/squeegees/how-to-choose-a-squeegee/
description: How to choose a squeegee blade for screen printing in India by ink type, material, print detail and press type, with a selection table and blade care advice.
last_updated: 2026-11-17
---

# How to choose a squeegee blade for your ink, material and press

Start with the ink: solvent and UV inks take a medium polyurethane blade, water-based and plastisol inks a softer one, conductive pastes a stabilised or triple-layer blade. Then adjust for the material, the detail in the image and the press type. The table below gives typical starting points; the ink maker's data sheet gives the exact figure.

## Step 1: the ink

The ink decides the blade material and the starting hardness. Solvent-based inks soak into ordinary polyurethane and soften it, so use a solvent-resistant grade such as RKS HT1 or Printan at 65 to 75 Shore A and rotate blades between shifts. UV inks must be printed in a thin, even film, so a medium to hard blade of 75 to 85 Shore A with a sharp square edge is the usual choice.

Water-based inks and plastisol are printed in heavier films, often on textiles or textured surfaces, so a softer blade of 60 to 70 Shore A suits them. Conductive silver and aluminium pastes for solar cells, sensors and printed electronics are thick and abrasive and must go down in exactly the same amount on every print, so the blade must keep its angle. RKS makes the HT3 triple-layer strip and the carbon-backed Carbon BW for these pastes, and the Carbon HT PK for solder paste. Check the ink maker's data sheet in every case.

## Step 2: the material

A flat, smooth substrate such as polycarbonate, polyester film, glass or coated board lets a hard blade seal properly, so go to the harder end of the ink's range. A textured, rough or uneven material, such as textile, leather, a moulded part or a rough laminate, needs a softer blade that follows the surface, or a rounded edge that fills the texture. If the material is not flat, check the press's off-contact and bed level before blaming the blade.

## Step 3: the detail in the image

Fine lines, small text and halftones need a sharp square edge on a hard blade, 75 to 85 Shore A, run at a steep angle with low pressure. RKS recommends 75 to 85 Shore A with a 1.5 mm edge on rotary units for fine lines, and the HT3 Hard 85/90/85 for extreme fine lines in paste. Solid areas and heavy deposits need more ink: a softer blade of 55 to 65 Shore A, a bevelled or rounded edge, a flatter angle and a slower stroke. Braille on labels is the extreme case, printed with a 3 mm edge at 55 Shore A on RKS rotary blades. Mixed jobs are usually printed with a medium blade and tuned by pressure and angle; if one part of the image always suffers, split the job into two screens with two blades.

## Step 4: the press

A flatbed press holds the blade in a print head that sets the angle, so a conventional strip or an RKS System or Carbon S stabilised blade both work; the stabilised blade is chosen when the same result must repeat over a long run or across shifts. A stop-cylinder press prints fast on thin sheets and benefits from a stiff blade that does not bend at speed. A roll-to-roll press with a rotary screen unit needs a thin, flexible rotary blade such as the RKS RS or RS WP, cut to the length of the unit. Solar and printed electronics lines from DEK, Baccini, EKRA, ASYS and HMI take RKS Carbon blades in machine-specific holders.

## Selection table: typical starting points

The figures are typical starting points, to be adjusted on the press. Where a number depends on the ink, check the ink maker's data sheet.

| Job | Hardness | Edge | Blade type |
|---|---|---|---|
| Solvent ink, graphics on film or sheet | 65 to 75 Shore A | Square | RKS HT1 Medium, Printan 70 to 75; rotate blades |
| UV ink, fine detail on polycarbonate or glass | 75 to 85 Shore A | Square, sharp | RKS HT1 Hard, Printan 80 to 85, or RKS System or Carbon S for long runs |
| Water-based or plastisol ink, textiles and textured surfaces | 60 to 70 Shore A | Square or rounded | Printan 65 to 70 or HT1 Soft |
| Conductive paste: solar cells, sensors, printed electronics | Per the paste data sheet; HT3 Soft to Hard | Chamfered on Carbon BW, 45 degrees | RKS HT3, Carbon BW in DEK, Baccini or EKRA holders |
| Solder paste, SMT, head gaskets | 65 to 85 Shore A | 30, 45 or 60 degree edge | RKS Carbon HT PK |
| Labels on a rotary screen unit, normal work | 65 Shore A, 2 mm edge | Rounded, small or large radius | RKS RS or RS WP |
| Labels, fine lines and halftones | 75 to 85 Shore A, 1.5 mm edge | Rounded, small radius | RKS RS CC or RS WP CC |
| Braille and very heavy deposits | 55 Shore A, 3 mm edge | Rounded | RKS RS or RS WP |

## Blade size and ordering

Cut the blade 2 to 5 cm longer than the image on each side and keep it clear of the frame. Choose the height for the holder: 20 to 50 mm strips for standard holders, 95, 105 or 115 mm stabilised blades for RKS holders. A 6 mm strip of a given hardness acts harder than an 8 mm strip. An RKS order names the series, height, polyurethane thickness, hardness, cut length and edge, so have these ready when sending an enquiry.

## Care and when to resharpen

Clean the blade after every run with the solvent the ink maker names, and never leave it standing in ink or solvent. Store blades flat, edge up, away from heat and sunlight. Rotate blades between shifts so a swollen blade recovers its hardness before it is used or ground again.

Resharpen when fine detail widens, the deposit rises without a settings change, a streak appears in the same place on every sheet, or the edge shows rounding or daylight against a straight edge. Many plants grind on a fixed schedule by print count. Use a squeegee grinder such as the RKS SM 600 TT and 1200 TT or the ATMA ATS sharpeners, in small passes. Replace the blade when the free height is too short to flex, when the polyurethane has hardened or cracked, or when a stabilised blade has separated from its carrier.

## Ask Sunstar

Sunstar Graphics supplies the full RKS squeegee range in India, with holders, adapter strips and grinding machines, and Kuroki polyurethane blades from Taiwan. Send an enquiry with your ink, mesh count, material, press model and image size and Sunstar will suggest a blade and quote a rate within one working day.

### Ask for a blade

Send the ink, mesh, material and press model. Sunstar suggests a blade and a price within one working day.

RKS and Kuroki squeegee blades, RKS holders and ATMA squeegee sharpeners

Type

Flat bed presses for rigid and flexible sheets up to 25 mm thick

Type

Reel to reel printers with camera registration and in-line curing

Type

SPS presses for flexible sheets at up to 4,000 sheets an hour

Type

Solar cells and PV glass

Application

Printed sensors and seat mats

Application

Labels and stickers

Application

Gaskets

Application

What is a squeegee in screen printing

Guide

Squeegee pressure, angle and hardness

Guide

Mesh count for conductive ink

Guide

UV ink not curing

Guide

## Related machines

Blades, holders and sharpeners named in this guide.

All squeegees and tools →

- [**RKS HT3**](https://www.sunstargraphics.com/machines/rks-ht3/): Three-layer polyurethane squeegee designed for the electronics industry, for printing polymer-like pastes and silver-containing print media.
- [**RKS CARBON BW**](https://www.sunstargraphics.com/machines/rks-carbon-bw/): Multi-component hybrid squeegee with a next-generation carbon carrier and a printing edge made from the RKS HT polyurethane, thermally moulded (not glued) and delivered ready to print.

- [**RKS CARBON HT PK**](https://www.sunstargraphics.com/machines/rks-carbon-ht-pk/): Carbon-fibre carrier combined with RKS high-performance HT polyurethane, with a plane-parallel sharp printing edge profiled on fully automatic machines, for SMT, head gaskets, 3D and similar precision printing.
- [**RKS PRINTAN (MONOFLEX / BIFLEX / TRIFLEX)**](https://www.sunstargraphics.com/machines/rks-printan/): Universal, colour-coded polyurethane squeegee strips for almost all screen-printing applications, in single, dual and triple-layer versions.

- [**RKS SYSTEM SQUEEGEE (Type 00 / Type 00 BW / Type 32 / Type 32 BW)**](https://www.sunstargraphics.com/machines/rks-rks-system/): The original RKS two-component squeegee: a fiberglass (GRP) spine integrally joined to an elastomer (Vulkollan) printing strip, so the blade keeps a plane-parallel printing edge and a constant angle throughout a production run.
- [**RKS SM 600 TT / SM 1200 TT**](https://www.sunstargraphics.com/machines/rks-sm-600-tt-1200-tt/): Lower-cost squeegee grinding machine with a double reversible grinding wheel, controlled grinding speed, vacuum extraction and automatic feed.

- [**ATMA AT-S100D**](https://www.sunstargraphics.com/machines/atma-ats-100d/): For sharpening squeegee blade on holder in order to obtain flat straight and sharp edges.

## From Sunstar Academy

Real footage and short lessons from Sunstar's own channel.

All videos →

### 5 Squeegee Mistakes That Reduce Your Print Quality

5 Things Every Screen Printing Operator Should Know About Their Squeegee

## Questions buyers ask

**Which squeegee hardness is best for UV ink?**

A medium to hard blade of 75 to 85 Shore A with a sharp square edge, because UV ink prints best as a thin, even film. Check the ink data sheet for the maker's range.

**Which squeegee is used for plastisol ink?**

A softer blade of 60 to 70 Shore A with a square or slightly rounded edge, because plastisol is printed in a heavy film, often on textiles.

**What squeegee is used for conductive silver paste?**

A blade that keeps its angle under a thick, abrasive paste: the RKS HT3 triple-layer strip, the carbon-backed RKS Carbon BW, or a diamond strip, in the holder made for the printing line.

**How do I know which squeegee my machine takes?**

Check the holder: standard holders take 20 to 50 mm polyurethane strips or a stabilised blade with an adapter strip; RKS holders take 95 to 115 mm stabilised blades; rotary units take thin rotary blades cut to the unit length. Sunstar confirms the fit from your press model.

## Ask for a blade.

Send the ink, mesh count, material, press model and image size. Sunstar suggests a blade and quotes within one working day.

## About Sunstar Graphics

- Company: Sunstar Graphics Pvt. Ltd., an Indian distributor of industrial screen printing machinery
- Since: 1980, founded as Sunglo India by Ajit Lalvani; Sunstar Graphics formed in 2000
- Brands: Authorised distributor in India for ATMA (Taiwan), SPS and RKS (Germany), Grünig and SignTronic (Switzerland) and Lingtie and Luen Cheong (China). It also supplies Kuroki squeegees (Taiwan).
- Supplies: printers (flatbed, stop-cylinder, roll-to-roll, glass, PCB and part printers); pre-press and screen making (stretching, coating, computer-to-screen, washing); dryers and curing (IR, hot air and UV); feeders, stackers and converting; squeegees and tools
- Services: Consultation, supply, installation, operator training, service, spares and AMC
- Area served: All of India, from the office in Worli, Mumbai
- Address: Unit B-305, Neelam Centre, S K Ahire Marg, Worli, Mumbai, Maharashtra 400030, India
- Phone: +91 98203 61705
- Email: Sales@sunstargraphics.com
- Prices: Quoted in Indian rupees for each job; not published as a list
