---
title: The Screen Printing Process | Pre-press, Printing, Curing
url: https://www.sunstargraphics.com/process/
description: How industrial screen printing works, step by step: screen making, printing and curing, with the machine Sunstar Graphics supplies for each stage in India.
last_updated: 2026-11-17
---

# The screen printing process, step by step

A print line has three stages: making the screen, printing, and curing. Sunstar supplies the machines for all three.

The six steps

All machines

- [Pre-press](https://www.sunstargraphics.com/process/pre-press-screen-making/): Print quality starts with the screen.
- [Printing](https://www.sunstargraphics.com/process/screen-printing-machines/): The press holds the substrate, brings the screen down and drives the squeegee.

- [Curing](https://www.sunstargraphics.com/process/uv-ir-curing-drying/): After the press, the ink has to be dried or cured before sheets are stacked or printed again.

## How a print is made

Six steps, six machines. The clips are illustrations of each step, generated with AI. They are not footage of a specific machine.

Stretch the mesh Illustration

Coat the emulsion Illustration

Image the stencil Illustration

Print the sheet Illustration

Cure in line Illustration

Cut to size Illustration

## The six steps in words

And the machine Sunstar supplies for each.

1. **Stretch the mesh** Polyester mesh is pulled to a set tension and glued to the frame. Even tension keeps register on every print after this. [Grünig G-STRETCH 281](https://www.sunstargraphics.com/machines/grunig-g-stretch-281/)
2. **Coat the emulsion** A trough of light-sensitive emulsion is drawn up the mesh in one pass, to an exact thickness. [Grünig G-COAT 414](https://www.sunstargraphics.com/machines/grunig-g-coat-414/)
3. **Image the stencil** A UV head writes the artwork straight onto the emulsion, without film. Where light hits, the emulsion hardens. The rest washes out. [SignTronic STM-ONE](https://www.sunstargraphics.com/machines/signtronic-stm-one/)
4. **Print the sheet** The screen drops to a few millimetres above the sheet. The squeegee presses the mesh down and pushes ink through. The flood bar then refills the mesh, and the screen lifts. [ATMA AT-80P/SV](https://www.sunstargraphics.com/machines/atma-at-80p-sv/)
5. **Cure in line** The sheet rides a conveyor under infrared or UV lamps. It leaves the tunnel dry and ready to stack. [Luen Cheong SD5000](https://www.sunstargraphics.com/machines/luen-cheong-lc-sd-5000/)
6. **Cut to size** For reel work, the printed web is registered by camera and cut to sheets, ready to ship. [Lingtie LTG-600](https://www.sunstargraphics.com/machines/lingtie-ltg-600/)

## Machine types by stage

- [Fully automatic flatbeds, cylinder presses and reel-fed printers](https://www.sunstargraphics.com/automatic-screen-printing-machine/): An automatic screen printing machine feeds the sheet, registers it, prints it and delivers it to the dryer without an operator handling each piece.
- [Operator-fed electric flatbeds and precision part printers](https://www.sunstargraphics.com/semi-automatic-screen-printing-machine/): A semi-automatic screen printing machine prints each sheet by motor while an operator loads and unloads it.

- [Flat bed presses for rigid and flexible sheets up to 25 mm thick](https://www.sunstargraphics.com/flatbed-screen-printing-machine/): A flatbed screen printing machine holds the sheet flat on a vacuum bed.
- [SPS presses for flexible sheets at up to 4,000 sheets an hour](https://www.sunstargraphics.com/stop-cylinder-screen-printing-press/): A stop-cylinder screen printing press grips a flexible sheet on a cylinder.

- [Reel to reel printers with camera registration and in-line curing](https://www.sunstargraphics.com/roll-to-roll-screen-printing-machine/): A roll-to-roll screen printing machine prints a continuous web of film or label stock from one reel to another.
- [Camera-aligned presses for fine lines and multilayer printing](https://www.sunstargraphics.com/ccd-registration-screen-printing-machine/): A CCD registration screen printing machine uses cameras to find register marks on the sheet or web before each print.

- [Feeder, press, dryer and stacker specified together as one line](https://www.sunstargraphics.com/automatic-screen-printing-line/): An automatic screen printing line joins the machines around the press so that sheets move through without being carried by hand.
- [Pneumatic mesh stretching to a set, repeatable tension](https://www.sunstargraphics.com/screen-stretching-machine/): A screen stretching machine pulls the mesh to a set tension in both directions and holds it while the mesh is glued to the frame.

- [Automatic emulsion coating to the same thickness on every screen](https://www.sunstargraphics.com/screen-coating-machine/): A screen coating machine applies photo emulsion to the stretched mesh.

By category: [printers](https://www.sunstargraphics.com/printers/), [pre-press](https://www.sunstargraphics.com/pre-press/), [dryers](https://www.sunstargraphics.com/dryers/), [handling](https://www.sunstargraphics.com/handling/), [squeegees](https://www.sunstargraphics.com/squeegees/).

## Guides

Settings and fixes for each stage.

All guides →

- [Screen tension in N/cm](https://www.sunstargraphics.com/guides/screen-tension-ncm-guide/): Screen tension is the pulling force in the stretched mesh, measured in newtons per centimetre (N/cm) with a tension meter resting on the mesh. Most polyester screens for industrial work run at about 16 to 30 N/cm. The right figure depends on the mesh count and thread diameter, and the mesh maker's data sheet gives it for each mesh.
- [Off-contact and snap-off](https://www.sunstargraphics.com/guides/off-contact-snap-off-screen-printing/): Off-contact distance, also called snap-off, is the gap between the underside of the screen and the substrate before the squeegee presses the mesh down. On a well-tensioned screen it is typically 1 to 3 mm for small frames and 3 to 8 mm for large frames. Use the smallest gap that lets the mesh lift cleanly behind the squeegee.

- [Squeegee pressure, angle and hardness](https://www.sunstargraphics.com/guides/squeegee-pressure-angle-hardness/): Squeegee pressure, angle and hardness together decide how much ink passes through the screen and how sharp the printed edge is. Use the lowest pressure that gives a complete print, an angle of about 70 to 75 degrees as a starting point, and a blade of 70 to 75 Shore A for general work. A softer blade, a flatter angle and a slower stroke all put down more ink.
- [Registration problems in multicolour printing](https://www.sunstargraphics.com/guides/registration-problems-multicolour-screen-printing/): Registration problems in multicolour screen printing come from four places: the screens, the substrate, the press and the artwork. Look at how the error behaves before changing anything. A constant error is a setup fault. A random error is a feeding fault. An error that grows across the sheet is a change of size in the screen or the substrate.

- [UV ink not curing](https://www.sunstargraphics.com/guides/uv-ink-not-curing-uv-dose/): UV ink that stays tacky, scratches off or fails a tape test has usually received too little UV energy for its film thickness and colour. Measure the UV dose on the belt with a radiometer, in mJ/cm², and compare it with the figure in the ink maker's data sheet. The common causes are an aged lamp, dirty reflectors, a belt running too fast and an ink film that is too thick.
- [Mesh count for conductive ink](https://www.sunstargraphics.com/guides/mesh-count-for-conductive-ink-silver-paste/): For silver and carbon conductive pastes on membrane switches and printed sensors, polyester mesh of about 61 to 90 threads per cm is typical. Finer tracks use polyester of 120 threads per cm or more, or stainless steel mesh of 325 to 400 threads per inch. Start with the mesh named in the paste maker's data sheet, because particle size and target resistance decide the choice.

## Questions buyers ask

**Why automate screen making?**

Tension, coating thickness and washout decide print quality. Automatic machines make every screen the same.

**Does Sunstar supply the full screen room?**

Yes. Stretching, coating, imaging, washing, drying and reclaiming, specified together.

**Does Sunstar install and service this machine in India?**

Yes. Sunstar engineers install the machine, train your operators on site and handle service and spares from Mumbai.

**What can a flatbed screen printer print on?**

Rigid and flexible sheets: polycarbonate, polyester, PVC, glass, metal and board, up to 25 mm thick.

**IR or UV dryer?**

IR and hot air for solvent, water-based and plastisol inks. UV for UV inks.

**How is a dryer sized?**

By the width of the sheet and the speed of the press, so the ink is cured at full output.

## Tell Sunstar what you print.

An engineer replies within one working day with machine options and Indian pricing. Delivered and installed anywhere in India.

## About Sunstar Graphics

- Company: Sunstar Graphics Pvt. Ltd., an Indian distributor of industrial screen printing machinery
- Since: 1980, founded as Sunglo India by Ajit Lalvani; Sunstar Graphics formed in 2000
- Brands: Authorised distributor in India for ATMA (Taiwan), SPS and RKS (Germany), Grünig and SignTronic (Switzerland) and Lingtie and Luen Cheong (China). It also supplies Kuroki squeegees (Taiwan).
- Supplies: printers (flatbed, stop-cylinder, roll-to-roll, glass, PCB and part printers); pre-press and screen making (stretching, coating, computer-to-screen, washing); dryers and curing (IR, hot air and UV); feeders, stackers and converting; squeegees and tools
- Services: Consultation, supply, installation, operator training, service, spares and AMC
- Area served: All of India, from the office in Worli, Mumbai
- Address: Unit B-305, Neelam Centre, S K Ahire Marg, Worli, Mumbai, Maharashtra 400030, India
- Phone: +91 98203 61705
- Email: Sales@sunstargraphics.com
- Prices: Quoted in Indian rupees for each job; not published as a list
