---
title: Pre-Press Screen Making Equipment India | Sunstar Graphics
url: https://www.sunstargraphics.com/pre-press/
description: Pre-press screen making equipment in India from Sunstar Graphics: stretching, coating, washing, developing, CTS, exposure and drying, process explained first.
last_updated: 2026-11-17
---

# Pre-press screen making machines: the steps, what to check, the range

Print quality is decided before the press, in the screen room. Mesh is stretched to tension on the frame, coated with emulsion to a set thickness, imaged with the artwork, developed, dried and checked. After the job the screen is washed, decoated and prepared for the next one. Each of these steps has a machine, and a screen that is wrong at any step prints wrong on every sheet.

See the range

Sunstar Graphics is the exclusive distributor in India for Grünig stretching, coating, washing and drying machines from Switzerland and SignTronic computer to screen (CTS) imaging systems from Switzerland, and also supplies ATMA screen making units. This page explains the process first, then what to check before buying, then the nine kinds of pre-press equipment in the range.

## How it works

1. **Stretch** The mesh is pulled to a set tension, measured in N/cm, and glued to the frame. Even tension across the screen is what keeps register and gives a clean snap-off. A stretching machine does this with pneumatic or mechanical clamps, repeatably.
2. **Coat** Emulsion is applied to the mesh with a trough. The thickness of emulsion over the mesh (EOM) sets the ink film and the edge definition. A coating machine applies the same number of passes at the same speed and angle every time.
3. **Image** The artwork is put onto the coated screen, either by exposing through a film positive in an exposure unit or by writing it directly onto the emulsion with a computer to screen system, with no film at all.
4. **Develop and wash out** Water washes away the emulsion that was not hardened, opening the image in the stencil. A developing machine does this with controlled nozzles and water, so fine lines open cleanly.
5. **Dry and check** The stencil is dried in a dust-free cabinet at a set temperature and inspected before it goes to the press.
6. **Reclaim** After printing, the screen is washed of ink, the stencil is decoated, and the frame is cleaned and degreased so the mesh can be coated again. Washing machines keep the solvent and water closed in, which protects the operator and cuts the cost of chemicals.

### Compare models

Put two or three machines side by side, specification by specification.

Open the comparison

### 67 models

ATMA, Grünig, SignTronic

All pre-press in the catalogue

### Ask an engineer

Send your material, sheet size and volume. An engineer replies with the right type and model.

## See the machines work

Animated models of the machines in this category, one cycle each. Press play.

All films →

**How a screen stretching machine works** Clamps grip the mesh on all four sides and pull it to a set tension in stages, letting it relax between pulls. The frame is raised to the mesh and glued. Animated model of this machine. Silent, 30 seconds. [Open the interactive 3D version](https://www.sunstargraphics.com/demos/grunig/)

**How computer-to-screen imaging works** The coated screen is clamped upright and a UV head scans across it, exposing the artwork directly onto the emulsion. No film positive is needed. Animated model of this machine. Silent, 30 seconds. [Open the interactive 3D version](https://www.sunstargraphics.com/demos/signtronic/)

## How to choose

What to settle before asking for a quotation.

Buying guides →

### Screen size

Measure the largest frame you use, outside dimensions, and the smallest. Every pre-press machine is sized by frame, and a frame that does not fit cannot be processed.

### Screens per day

Count how many screens you stretch, coat, image and reclaim in a day. A few screens a day are done by hand or on manual units; dozens need automatic machines, and the busiest step sets the pace.

### Mesh and detail

Fine mesh counts, high tension and fine lines (membrane switches, electronics, dials) need an accurate stretcher, an automatic coater and CTS imaging. Coarse work needs less.

### Film or CTS

If you still make film positives, compare the cost and time of film against a computer to screen system, which images straight from the file and removes film, registration of film to screen and most pinholes.

### Water, chemicals, space

Washing and developing need a water supply and drainage, and a place for used chemicals. Check the room, the ventilation and the floor load before choosing the machine size.

## Screen stretching machines

Pneumatic and mechanical stretchers that pull mesh to a set tension and hold it while the frame is glued, from one frame to large-format and automatic units.

All 15 models →

- [**ATMA A-211**](https://www.sunstargraphics.com/machines/atma-a-211/): Screen fabric stretcher.
- [**ATMA TY-MS45**](https://www.sunstargraphics.com/machines/atma-ty-ms45/): For stretching screen fabric to make a screen printing stencil, robust structure fulfills requirement on high tension / bias-angle stretching.

- [**ATMA TY-MS56**](https://www.sunstargraphics.com/machines/atma-ty-ms56/): For stretching screen fabric to make a screen printing stencil, robust structure fulfills requirement on high tension / bias-angle stretching.
- [**Grünig G-CHECK**](https://www.sunstargraphics.com/machines/grunig-g-check/): Mechanical mesh tension measuring device (10 to 50 N/cm) that operates entirely without battery or mains supply.

[All 15 models in the catalogue →](https://www.sunstargraphics.com/machines/?cat=pre-press&q=stretching)

## Screen coating machines

Automatic emulsion coaters that apply the same EOM on every screen, with trough and spatula accessories.

All 11 models →

- [**Grünig G-COAT 414**](https://www.sunstargraphics.com/machines/grunig-g-coat-414/): G-COAT 414 – the economical and flexible coating machine for screen sizes of up to 2 x 2 meters.
- [**ATMA AT-C1012D**](https://www.sunstargraphics.com/machines/atma-at-c1012d/): This model is specialized in high precise coating even layer of photoimageable emulsion onto screen mesh.

- [**ATMA AT-C1216D**](https://www.sunstargraphics.com/machines/atma-at-c1216d/): This coating machine is specialized in high precision coating photoimageable emulsion onto screen mesh.
- [**ATMA C 1012 / C 1016**](https://www.sunstargraphics.com/machines/atma-c-1012-c-1016/): Screen coating machine.

[All 11 models in the catalogue →](https://www.sunstargraphics.com/machines/?cat=pre-press&q=coating)

## Screen washing machines

Closed cabinets that wash ink from screens with solvent, with filtering and recycling of the washing liquid.

All 12 models →

- [**Grünig G-WASH 034**](https://www.sunstargraphics.com/machines/grunig-g-wash-034/): The Fluid Recycling System has been designed for universal use; it improves the quality and lifetime of process liquids.
- [**Grünig G-WASH 040XS**](https://www.sunstargraphics.com/machines/grunig-g-wash-040xs/): The inclined filter-based cleaning system allows simple, safe and efficient IN-HOUSE cleaning of various liquids, in addition to lowering your operating expenses.

- [**Grünig G-WASH 101**](https://www.sunstargraphics.com/machines/grunig-g-wash-101/): Grünig special nozzles made of stainless steel V2A, robust and easy to maintain thanks to the unique pivoting service cover.
- [**Grünig G-WASH 104**](https://www.sunstargraphics.com/machines/grunig-g-wash-104/): Automatic screen washing machine in PLUG & WASH construction (unpack, set up, connect, wash) with ecological closed-circuit operation.

[All 12 models in the catalogue →](https://www.sunstargraphics.com/machines/?cat=pre-press&q=washing)

## Developing and decoating machines

Water washout units that open the stencil after exposure, and decoating units that strip the old stencil for reuse.

- [**ATMA A 521**](https://www.sunstargraphics.com/machines/atma-a-521/): Developing and drying unit.
- [**Grünig G 104 A 2**](https://www.sunstargraphics.com/machines/grunig-g-104-a-2/): Developing

- [**Grünig G 106**](https://www.sunstargraphics.com/machines/grunig-g-106/): Developing
- [**Grünig G-WASH 106**](https://www.sunstargraphics.com/machines/grunig-g-wash-106/): Automatic screen developing machine in PLUG & WASH construction, available as A1 for pure clean water operation or A2 for ecological closed-circuit operation.

## Computer to screen (CTS) systems

Imaging units that write the artwork straight onto the coated screen with UV light, so no film positive is needed.

All 7 models →

- [**SignTronic STM-ONE**](https://www.sunstargraphics.com/machines/signtronic-stm-one/): Compact CtS system for small to medium stencil volumes with an attractive entry price.
- [**SignTronic STM CtS IN-LINE OPTION**](https://www.sunstargraphics.com/machines/signtronic-stm-cts-in-line-option/): Modular automation concepts ranging from loading stations to fully automated, print-ready stencil production.

- [**SignTronic STM-D Series**](https://www.sunstargraphics.com/machines/signtronic-stm-d-series/): Modular CtS concept for large frame formats – expandable up to full IN-LINE integration.
- [**SignTronic STM-MICRO**](https://www.sunstargraphics.com/machines/signtronic-stm-micro/): Compact solution for small formats with optimized handling and high imaging quality.

[All 7 models in the catalogue →](https://www.sunstargraphics.com/machines/?cat=pre-press&q=cts)

## Exposure units

UV units that harden the emulsion through a film positive, with vacuum frames to hold film and screen in contact.

- [**ATMA A411**](https://www.sunstargraphics.com/machines/atma-a411-4860a/): For exposure-transfering artwork image on positive film to photosensitive emulsion layter coated on a screen.

## Screen drying cabinets

Dust-free horizontal and vertical cabinets that dry coated and developed screens at a set temperature.

All 7 models →

- [**ATMA A541(3648)**](https://www.sunstargraphics.com/machines/atma-a541-3648/): For rapid drying screen stencil(s).
- [**ATMA A541(4252)**](https://www.sunstargraphics.com/machines/atma-a541-4252/): For rapid drying screen stencil(s).

- [**ATMA A542(3939V)**](https://www.sunstargraphics.com/machines/atma-a542-3939v/): For rapid drying screen stencil(s).
- [**ATMA A542(4848V)**](https://www.sunstargraphics.com/machines/atma-a542-4848v/): For rapid drying screen stencil(s).

[All 7 models in the catalogue →](https://www.sunstargraphics.com/machines/?cat=pre-press&q=screen-drying)

## Frame preparation

Units that clean, degrease and prepare frames for stretching and for the next coat.

- [**Grünig G-PREP 370**](https://www.sunstargraphics.com/machines/grunig-g-prep-370/): G-PREP 370 - Removes adhesive residues from screen printing frames quickly, cleanly, safely and wear-free.

## Screen room automation

Magazines, handling and software that move screens between machines and log the process.

All 9 models →

- [**Grünig G-FrameManager**](https://www.sunstargraphics.com/machines/grunig-g-framemanager/): Manages frames, meshes and storage positions in a database.
- [**Grünig G-GATEWAY**](https://www.sunstargraphics.com/machines/grunig-g-gateway/): The G-GATEWAY is the central junction point between the machine, the data acquisition, the process control and visualization.

- [**Grünig G-MPS**](https://www.sunstargraphics.com/machines/grunig-g-mps/): Create measurement reports with automatic measurements from various measuring devices.
- [**Grünig G-MagView**](https://www.sunstargraphics.com/machines/grunig-g-magview/): This application can display and easily manage magazine positions.

[All 9 models in the catalogue →](https://www.sunstargraphics.com/machines/?cat=pre-press&q=automation)

## Machine types in this category

Each page explains one class of machine and lists its models.

- [Pneumatic mesh stretching to a set, repeatable tension](https://www.sunstargraphics.com/screen-stretching-machine/): A screen stretching machine pulls the mesh to a set tension in both directions and holds it while the mesh is glued to the frame.
- [Automatic emulsion coating to the same thickness on every screen](https://www.sunstargraphics.com/screen-coating-machine/): A screen coating machine applies photo emulsion to the stretched mesh.

- [Washing, developing, decoating and reclaiming screens by machine](https://www.sunstargraphics.com/screen-washing-machine/): A screen washing machine cleans the screen with spray nozzles inside a closed cabinet.
- [Film-free imaging: artwork goes from the file to the screen](https://www.sunstargraphics.com/computer-to-screen-cts-machine/): A computer to screen machine, or CTS, writes the artwork onto the coated screen with UV light, straight from the file.

## Guides

Written for the person choosing the machine.

All guides →

- [Screen printing vs digital printing for industrial parts](https://www.sunstargraphics.com/guides/screen-printing-vs-digital-printing-industrial/): Screen printing is the better process for volume production, for thick or opaque ink films and for functional inks such as silver, carbon and glass enamel. Digital printing is better for short runs, many design versions and variable data. It is common to use digital for samples and screen printing for production.
- [How membrane switches are made](https://www.sunstargraphics.com/guides/how-membrane-switches-are-made/): A membrane switch is made by screen printing a graphic overlay and one or two circuit layers on plastic film, then cutting them and laminating them with a spacer and adhesive. The circuit is printed in silver and carbon ink, with a dielectric layer for insulation. Each printed layer is dried or cured before the next, and each has to register to the others.

- [How glucose test strips are screen printed](https://www.sunstargraphics.com/guides/how-glucose-test-strips-are-screen-printed/): A glucose test strip is made by screen printing carbon and silver electrodes on plastic film, printing an insulation layer that leaves a small electrode area open, and adding the enzyme reagent. Many strips are printed side by side on one sheet or along a reel, then covered and cut apart. The electrode area sets the reading, so line width, ink deposit and register are held tightly.
- [Fine-line screen printing on polycarbonate](https://www.sunstargraphics.com/guides/fine-line-screen-printing-polycarbonate/): Fine lines on polycarbonate need four things to be right together: a fine mesh at high tension, a thin and flat stencil with a sharp image, a sharp squeegee at low pressure, and a clean, flat sheet free of static. Lines of around 100 to 150 microns are typically achievable on a well set flatbed press. Finer lines need closer control of every step.

- [Screen tension in N/cm](https://www.sunstargraphics.com/guides/screen-tension-ncm-guide/): Screen tension is the pulling force in the stretched mesh, measured in newtons per centimetre (N/cm) with a tension meter resting on the mesh. Most polyester screens for industrial work run at about 16 to 30 N/cm. The right figure depends on the mesh count and thread diameter, and the mesh maker's data sheet gives it for each mesh.
- [Off-contact and snap-off](https://www.sunstargraphics.com/guides/off-contact-snap-off-screen-printing/): Off-contact distance, also called snap-off, is the gap between the underside of the screen and the substrate before the squeegee presses the mesh down. On a well-tensioned screen it is typically 1 to 3 mm for small frames and 3 to 8 mm for large frames. Use the smallest gap that lets the mesh lift cleanly behind the squeegee.

Other categories: [Printers](https://www.sunstargraphics.com/printers/), [Dryers and curing](https://www.sunstargraphics.com/dryers/), [Feeders, stackers and converting](https://www.sunstargraphics.com/handling/), [Squeegees and tools](https://www.sunstargraphics.com/squeegees/). See the [process stage by stage](https://www.sunstargraphics.com/process/) or [start from what you print](https://www.sunstargraphics.com/applications/).

## From Sunstar Academy

Real footage and short lessons from Sunstar's own channel.

All videos →

### ATMA A211 Pneumatic Screen Stretching System

Discover the ATMA A211 Pneumatic Screen Stretching System, designed for consistent screen tension, faster setup, and reliable screen preparation for professional screen…

## Questions buyers ask

**What equipment is needed for screen making?**

A stretching machine, a coating machine, an exposure unit or computer to screen system, a developing or washout unit, a drying cabinet and a washing machine for reclaiming. Small shops do some steps by hand.

**What is a computer to screen machine?**

A CTS system images the artwork directly onto the coated screen from the file, using UV light, with no film positive. It saves film, removes film-to-screen registration and gives a sharper stencil.

**What screen tension is needed for screen printing?**

It depends on the mesh and the job; typical industrial values are in the range of 20 to 30 N/cm, and fine work runs at the higher end. Measure every screen with a tension meter and check the mesh maker's data.

**Which Grünig machines does Sunstar supply in India?**

Grünig G-STRETCH stretching, G-COAT coating, G-WASH washing, developing and decoating, G-DRY drying cabinets and G-PREP frame preparation, with installation, training and service from Mumbai.

## Tell Sunstar what you print.

An engineer replies within one working day with the right type and model, and Indian pricing. Delivered and installed anywhere in India.

## About Sunstar Graphics

- Company: Sunstar Graphics Pvt. Ltd., an Indian distributor of industrial screen printing machinery
- Since: 1980, founded as Sunglo India by Ajit Lalvani; Sunstar Graphics formed in 2000
- Brands: Authorised distributor in India for ATMA (Taiwan), SPS and RKS (Germany), Grünig and SignTronic (Switzerland) and Lingtie and Luen Cheong (China). It also supplies Kuroki squeegees (Taiwan).
- Supplies: printers (flatbed, stop-cylinder, roll-to-roll, glass, PCB and part printers); pre-press and screen making (stretching, coating, computer-to-screen, washing); dryers and curing (IR, hot air and UV); feeders, stackers and converting; squeegees and tools
- Services: Consultation, supply, installation, operator training, service, spares and AMC
- Area served: All of India, from the office in Worli, Mumbai
- Address: Unit B-305, Neelam Centre, S K Ahire Marg, Worli, Mumbai, Maharashtra 400030, India
- Phone: +91 98203 61705
- Email: Sales@sunstargraphics.com
- Prices: Quoted in Indian rupees for each job; not published as a list
