---
title: UV Ink Not Curing: UV Dose for Screen Printing Explained
url: https://www.sunstargraphics.com/guides/uv-ink-not-curing-uv-dose/
description: UV ink not curing in screen printing: check UV dose in mJ/cm², lamp age, belt speed and ink film. Causes, fixes and UV curing machines supplied in India.
last_updated: 2026-11-17
---

# Why UV ink is not curing and how to check the UV dose

UV ink that stays tacky, scratches off or fails a tape test has usually received too little UV energy for its film thickness and colour. Measure the UV dose on the belt with a radiometer, in mJ/cm², and compare it with the figure in the ink maker's data sheet. The common causes are an aged lamp, dirty reflectors, a belt running too fast and an ink film that is too thick.

## UV dose and intensity

Dose is the total UV energy that reaches the print, in mJ/cm². It rises when lamp power goes up or the belt slows down. Halving the belt speed roughly doubles the dose. Intensity, also called irradiance, is the peak power at the print surface in mW/cm². It depends on lamp power, reflector condition and lamp height. An ink needs enough of both.

Many graphic UV screen inks are specified at roughly 150 to 400 mJ/cm². Opaque whites, dense blacks and thick textured varnishes need more. These are typical figures. Use the dose in the ink maker's data sheet, and measure with the same type of radiometer, because instruments read different UV bands.

## Checks to make, in order

- Lamp age. Mercury UV lamps lose output with use, and many are replaced at around 1,000 hours. Check the lamp maker's figure and log the hours.
- Reflectors and lamp surface. Dust and ink mist cut the UV that reaches the belt. Clean them as the dryer manual describes.
- Belt speed. Confirm the real speed with a tape and a stopwatch.
- Ink film. A coarse mesh or thick stencil can lay down more ink than the lamp cures through. Try a finer mesh.
- Colour. Black, white and metallic inks block UV. Slow the belt or add a second pass.
- Ink condition. Old stock, too much thinner and unmixed additives all slow the cure.
- Lamp type. LED UV units need inks made for their wavelength. An ink made for mercury lamps may stay wet under LED.

## Symptoms and fixes

| Problem | Likely cause | Fix |
|---|---|---|
| Surface stays tacky | Low dose or low intensity | Check lamp hours and reflectors, slow the belt, measure the dose |
| Surface is dry but the ink scratches off | Bottom of the film is under-cured, or the substrate has low surface energy | Reduce the ink film, slow the belt, check the substrate with the ink maker |
| Ink is brittle and cracks on cutting, or the next colour does not bond | Over-cure | Raise the belt speed on the earlier colours |
| Cure differs across the belt | Lamp ends have aged or a reflector is dirty | Measure the dose at left, centre and right |

## Testing the cure

Test on the production material. A thumb twist and a fingernail scratch give a quick check at the dryer exit. A cross-hatch tape test gives a result you can record. Some UV inks keep gaining adhesion for up to 24 hours, so follow the test timing in the data sheet. Take a radiometer reading at the start of each shift and keep the log.

## UV curing machines Sunstar supplies

Sunstar Graphics supplies Luen Cheong UV curing machines in India. The TM-UV/F range of UV dryers runs from the TM-200 to the TM-1200, and Sunstar sizes the UV conveyor dryer to the width of the sheet and the speed of the press. For lines that run both solvent and UV inks, the SD+TM 1100UVF and the UV 8000 are combined IR + UV drying ovens.

Sunstar installs and services the dryers from Mumbai. Send an enquiry with your ink, substrate and press speed for machine options and Indian pricing.

## Machines for this

Supplied in India by Sunstar.

- [**Luen Cheong TM-800UVF**](https://www.sunstargraphics.com/machines/luen-cheong-tm-800-uv-f/): Our latest innovation, the TM-800UVF UV Curing Machine, is engineered for performance in a wide range of industrial applications.
- [**Luen Cheong TM-500UVF**](https://www.sunstargraphics.com/machines/luen-cheong-tm-500-uv-f/): Our TM-500UVF UV Curing Machine is a versatile solution designed for a wide range of UV drying, printing, and polishing applications.

- [**Luen Cheong SD+TM-1100UVF**](https://www.sunstargraphics.com/machines/luen-cheong-sd-tm-1100uvf/): This integrated IR drying tunnel and UV curing machine offers a comprehensive solution for flat product finishing.
- [**Luen Cheong SD-UV8000**](https://www.sunstargraphics.com/machines/luen-cheong-uv-8000/): An integrated solution combining Infrared (IR) drying and Ultraviolet (UV) curing for efficient post-printing and coating processes.

## Short answers

**Why is my UV ink still tacky after curing?**

The print has not received enough UV energy. Check lamp hours, clean the reflectors, slow the belt and measure the dose with a radiometer.

**What UV dose is needed for screen printing ink?**

Many graphic UV screen inks need roughly 150 to 400 mJ/cm², and opaque or thick films need more. The ink maker's data sheet gives the figure for each ink.

**Can UV ink be over-cured?**

Yes. Too much UV makes the film brittle and can stop the next colour bonding to it. Set the dose to the data sheet value.

**How long does a UV lamp last?**

Mercury UV lamps are often replaced at around 1,000 hours, though this varies by lamp. Follow the lamp maker's figure and track output with a radiometer.

### Ask an engineer

Tell Sunstar what you print. An engineer replies within one working day with machine options and Indian pricing.

UV curing machines

8 models

IR and hot-air conveyor dryers

8 models

Spot UV and special effects

Labels, nameplates and packaging

Vehicle decals and graphics

Automotive

Nameplates and metal labels

Labels, nameplates and packaging

Labels and stickers

Labels, nameplates and packaging

All applications →

Screen printing defects

Guide

Squeegee pressure, angle and hardness

Guide

Emulsion thickness (EOM)

Guide

All guides →

## From Sunstar Academy

Real footage and short lessons from Sunstar's own channel.

All videos →

### Why Your Ink Viscosity Is Costing You Quality & Money

Ink viscosity can affect much more than how easily ink flows. It can influence print consistency, opacity, adhesion, dot gain, and rejection rates.

## Tell Sunstar what you print.

An engineer replies within one working day with machine options and Indian pricing.

## About Sunstar Graphics

- Company: Sunstar Graphics Pvt. Ltd., an Indian distributor of industrial screen printing machinery
- Since: 1980, founded as Sunglo India by Ajit Lalvani; Sunstar Graphics formed in 2000
- Brands: Authorised distributor in India for ATMA (Taiwan), SPS and RKS (Germany), Grünig and SignTronic (Switzerland) and Lingtie and Luen Cheong (China). It also supplies Kuroki squeegees (Taiwan).
- Supplies: printers (flatbed, stop-cylinder, roll-to-roll, glass, PCB and part printers); pre-press and screen making (stretching, coating, computer-to-screen, washing); dryers and curing (IR, hot air and UV); feeders, stackers and converting; squeegees and tools
- Services: Consultation, supply, installation, operator training, service, spares and AMC
- Area served: All of India, from the office in Worli, Mumbai
- Address: Unit B-305, Neelam Centre, S K Ahire Marg, Worli, Mumbai, Maharashtra 400030, India
- Phone: +91 98203 61705
- Email: Sales@sunstargraphics.com
- Prices: Quoted in Indian rupees for each job; not published as a list
