---
title: Squeegee Pressure, Angle and Hardness in Screen Printing
url: https://www.sunstargraphics.com/guides/squeegee-pressure-angle-hardness/
description: Squeegee pressure, angle and hardness for screen printing: typical settings, what each one changes, blade care, and RKS and Kuroki squeegees supplied in…
last_updated: 2026-11-17
---

# How to set squeegee pressure, angle and hardness

Squeegee pressure, angle and hardness together decide how much ink passes through the screen and how sharp the printed edge is. Use the lowest pressure that gives a complete print, an angle of about 70 to 75 degrees as a starting point, and a blade of 70 to 75 Shore A for general work. A softer blade, a flatter angle and a slower stroke all put down more ink.

## Typical settings and what each one changes

The ranges below are typical. Inks behave differently, so check the ink maker's data sheet for the recommended blade and mesh. Some presses show the angle from vertical, so 75 degrees to the screen reads as 15 degrees on the scale.

| Setting | Typical range | Effect |
|---|---|---|
| Hardness | 60 to 90 Shore A. Soft is 60 to 65, medium 70 to 75, hard 80 to 90 | Softer gives more ink and suits uneven surfaces. Harder gives less ink and sharper detail |
| Angle | 60 to 80 degrees between blade and screen | A more upright blade deposits less ink. A flatter blade deposits more |
| Pressure | The lowest that prints the full image | Extra pressure bends the blade, flattens the real angle and spreads the ink |
| Speed | Set by the ink. Thick pastes run slower | A slower stroke gives the ink more time to fill the mesh |
| Edge | Square and sharp for most work | A rounded or worn edge deposits more ink and softens the print |

## Setting squeegee pressure

Bring the squeegee down until it only just fails to print, then add pressure in small steps until the whole image prints cleanly. Stop there. Add a small margin only if parts of the image drop out during the run.

Too much pressure is a common fault on the shop floor. It forces ink under the stencil, widens fine lines, wears the stencil and mesh, and pulls the image out of register. If a print needs heavy pressure to clear, check for low screen tension, too much off-contact, a worn blade or a bed that is out of level.

Pressure must be even along the blade. Check that both ends of the holder are set to the same value.

## Choosing hardness and blade type

Solvents swell polyurethane. Rotate blades between shifts and let a used blade rest before sharpening, so the edge is ground after it has returned to size.

- Fine lines, halftones and thin UV films: hard blade, 80 Shore A or more, with a sharp edge.
- General graphics on film and sheet: medium blade, 70 to 75 Shore A.
- Heavy deposits, textured surfaces and textiles: soft blade, 60 to 65 Shore A.
- Long strokes and wide formats: a carbon-backed blade, which puts a printing edge of the hardness you need on a stiff backing, so it stays straight under pressure.

## Blade care

A squeegee prints with its edge. A nick prints as a streak, and a rounded edge raises the deposit across the whole image. Sharpen blades on a regular schedule and record which blade ran which job. Cut the blade about 2 to 5 cm longer than the image on each side and keep it clear of the frame. Set the flood bar so that it fills the mesh evenly without pushing ink through it.

## Squeegees and sharpeners Sunstar supplies

Sunstar Graphics supplies RKS squeegee blades from Germany in India. RKS HT3 is a polyurethane squeegee in soft, medium and hard grades. RKS Carbon HT PK and Carbon BW are carbon-backed squeegees that stay straight on long strokes. Sunstar also supplies Kuroki polyurethane blades from Taiwan. The ATMA ATS 100D digital squeegee sharpener and the ATS 100 / 150 squeegee sharpener restore the edge.

On the press, ATMA flatbed screen printers use a servo print stroke. Send an enquiry with your ink, mesh and print size for blade grades, machine options and Indian pricing.

## Machines for this

Supplied in India by Sunstar.

- [**RKS HT3**](https://www.sunstargraphics.com/machines/rks-ht3/): Three-layer polyurethane squeegee designed for the electronics industry, for printing polymer-like pastes and silver-containing print media.
- [**RKS CARBON HT PK**](https://www.sunstargraphics.com/machines/rks-carbon-ht-pk/): Carbon-fibre carrier combined with RKS high-performance HT polyurethane, with a plane-parallel sharp printing edge profiled on fully automatic machines, for SMT, head gaskets, 3D and similar precision printing.

- [**RKS CARBON BW**](https://www.sunstargraphics.com/machines/rks-carbon-bw/): Multi-component hybrid squeegee with a next-generation carbon carrier and a printing edge made from the RKS HT polyurethane, thermally moulded (not glued) and delivered ready to print.
- [**ATMA AT-S100D**](https://www.sunstargraphics.com/machines/atma-ats-100d/): For sharpening squeegee blade on holder in order to obtain flat straight and sharp edges.

## Short answers

**What is the correct squeegee angle for screen printing?**

About 70 to 75 degrees to the screen is a common starting point, within a typical range of 60 to 80 degrees. A more upright blade deposits less ink and a flatter blade deposits more.

**Which squeegee hardness should I use?**

Use 70 to 75 Shore A for general work, 80 or more for fine detail, and 60 to 65 for heavy deposits. Check the ink maker's data sheet for its recommendation.

**How much squeegee pressure is needed?**

Use the lowest pressure that prints the complete image. More pressure than that widens lines and wears the stencil.

**How often should a squeegee blade be sharpened?**

Sharpen it when the edge shows nicks or rounding, or on a fixed schedule based on print count. Let the blade rest after use so that solvent swelling has gone before grinding.

### Ask an engineer

Tell Sunstar what you print. An engineer replies within one working day with machine options and Indian pricing.

Squeegee blades and sharpeners

8 models

Flatbed screen printing machines

19 models

Printed sensors and seat mats

Electronics

Gaskets

Automotive

Membrane switches and overlays

Electronics

All applications →

Off-contact and snap-off

Guide

Screen printing defects

Guide

Mesh count for conductive ink

Guide

All guides →

## From Sunstar Academy

Real footage and short lessons from Sunstar's own channel.

All videos →

### 5 Squeegee Mistakes That Reduce Your Print Quality

5 Things Every Screen Printing Operator Should Know About Their Squeegee

## Tell Sunstar what you print.

An engineer replies within one working day with machine options and Indian pricing.

## About Sunstar Graphics

- Company: Sunstar Graphics Pvt. Ltd., an Indian distributor of industrial screen printing machinery
- Since: 1980, founded as Sunglo India by Ajit Lalvani; Sunstar Graphics formed in 2000
- Brands: Authorised distributor in India for ATMA (Taiwan), SPS and RKS (Germany), Grünig and SignTronic (Switzerland) and Lingtie and Luen Cheong (China). It also supplies Kuroki squeegees (Taiwan).
- Supplies: printers (flatbed, stop-cylinder, roll-to-roll, glass, PCB and part printers); pre-press and screen making (stretching, coating, computer-to-screen, washing); dryers and curing (IR, hot air and UV); feeders, stackers and converting; squeegees and tools
- Services: Consultation, supply, installation, operator training, service, spares and AMC
- Area served: All of India, from the office in Worli, Mumbai
- Address: Unit B-305, Neelam Centre, S K Ahire Marg, Worli, Mumbai, Maharashtra 400030, India
- Phone: +91 98203 61705
- Email: Sales@sunstargraphics.com
- Prices: Quoted in Indian rupees for each job; not published as a list
