---
title: Screen Printing Defects: Troubleshooting Causes and Fixes
url: https://www.sunstargraphics.com/guides/screen-printing-defects-troubleshooting/
description: Screen printing defects troubleshooting: causes and fixes for pinholes, sawtooth edges, bleeding, smudging, moiré and uneven deposit. For factories in India.
last_updated: 2026-11-17
---

# Screen printing defects troubleshooting: pinholes, sawtooth edges, bleeding, smudging and moiré

Most screen printing defects come from the screen, the squeegee, the ink or the off-contact setting. The table below gives the usual cause and fix for pinholes, sawtooth edges, bleeding, smudging, moiré and uneven deposit. Change one setting at a time and keep a record of what worked.

## Defects, causes and fixes

| Defect | Likely cause | Fix |
|---|---|---|
| Pinholes | Dust on the screen, film or exposure glass. Mesh not degreased. Under-exposed stencil. Dust or bubbles in the ink | Degrease and dry screens in a clean cabinet. Clean the glass. Expose fully. Touch up with blockout. Let stirred ink rest |
| Sawtooth edges | Stencil too thin or too rough, so the edge follows the mesh threads. Mesh too coarse for the line. Lines running along the threads | Raise the EOM or add face coats. Use a finer mesh. Stretch the mesh at an angle. Check exposure |
| Bleeding | Ink too thin. Too much squeegee pressure. Soft or rounded blade. Heavy flood. Rough stencil underside | Use less thinner. Reduce pressure. Fit a harder, sharp blade. Lighten the flood stroke. Improve the stencil |
| Smudging | Screen not lifting from the print because of low tension or low off-contact. Ink built up under the stencil. Sheet moving on the bed. Wet sheets touching | Check tension and raise the off-contact a little. Wipe the underside. Check vacuum. Dry fully before stacking |
| Moiré | Halftone dots clash with the mesh threads | Change the mesh count or mesh angle. Change the halftone angle. Check the film against the mesh before exposing |
| Uneven deposit | Worn or nicked squeegee. Pressure unequal along the blade. Uneven tension. Off-contact unequal. Ink thickening during the run | Sharpen or change the blade. Level the squeegee. Measure tension. Reset off-contact at four corners. Add fresh ink little and often |

## Find where the defect comes from

Look at ten prints in a row. A defect in the same place on every sheet is in the screen or stencil. A defect that moves about is dust, ink or the substrate. A defect that gets worse during the run points to ink drying in the mesh, ink building up under the stencil or a screen losing tension.

Check the stencil with a magnifier before it goes to press. Many pinholes and sawtooth edges can be seen there, and remaking a screen costs less than a batch of rejects.

## Screen room habits that prevent defects

- Degrease every screen and dry it in a closed, dust-free dryer.
- Measure tension after each reclaim and keep a lower limit.
- Coat to a set recipe and check stencil thickness.
- Run an exposure step test for each mesh and emulsion.
- Keep the coating and exposure area clean and at steady humidity.

## Press habits that prevent defects

Moiré is worth a test before production. A common guide is a mesh count at least four times the halftone ruling. The reliable check is to lay the film on the stretched mesh and turn it until the pattern disappears.

- Use the lowest squeegee pressure that prints the full image.
- Set off-contact equal at all four corners.
- Sharpen blades on a schedule.
- Follow the ink maker's data sheet for thinner, mesh and drying.
- Clean the substrate and control static on plastic films.

## Machines Sunstar supplies that address these defects

Sunstar Graphics supplies machines for each of these variables in India. Grünig stretching machines set the tension. Grünig G-COAT coating machines apply emulsion to a repeatable thickness, and Grünig G-WASH machines wash and develop screens. SignTronic computer-to-screen (CTS) imaging removes film and the dust that comes with it. RKS and Kuroki squeegees and ATMA squeegee sharpeners keep the blade edge consistent. ATMA flatbed (flat bed) screen printers use a motor-driven vertical screen lift and a servo print stroke.

Sunstar installs the machines, trains operators and services them from Mumbai, across India. Send an enquiry describing the defect, your ink and your material for machine options and Indian pricing.

## Machines for this

Supplied in India by Sunstar.

- [**Grünig G-COAT 414**](https://www.sunstargraphics.com/machines/grunig-g-coat-414/): G-COAT 414 – the economical and flexible coating machine for screen sizes of up to 2 x 2 meters.
- [**Grünig G-WASH 104**](https://www.sunstargraphics.com/machines/grunig-g-wash-104/): Automatic screen washing machine in PLUG & WASH construction (unpack, set up, connect, wash) with ecological closed-circuit operation.

- [**RKS HT3**](https://www.sunstargraphics.com/machines/rks-ht3/): Three-layer polyurethane squeegee designed for the electronics industry, for printing polymer-like pastes and silver-containing print media.
- [**ATMA AT-S100D**](https://www.sunstargraphics.com/machines/atma-ats-100d/): For sharpening squeegee blade on holder in order to obtain flat straight and sharp edges.

## Short answers

**What causes pinholes in screen printing?**

Dust on the screen, film or exposure glass, mesh that was not degreased, or an under-exposed stencil. Dust and air bubbles in the ink also print as pinholes.

**How do I fix sawtooth edges in screen printing?**

Increase the emulsion over mesh, smooth the print side with face coats, or use a finer mesh. Stretching the mesh at an angle also helps on straight lines.

**Why is my screen print smudging?**

The screen is not lifting cleanly from the print, or wet sheets are touching. Check screen tension, raise the off-contact slightly and make sure prints are dry before stacking.

**How do I avoid moiré in halftone screen printing?**

Choose a mesh count that does not clash with the halftone ruling and change the mesh or halftone angle. Check the film against the mesh before exposing the screen.

### Ask an engineer

Tell Sunstar what you print. An engineer replies within one working day with machine options and Indian pricing.

Screen coating machines

8 models

Screen washing machines

10 models

Squeegee blades and sharpeners

8 models

Touch panels and cover glass

Electronics

Nameplates and metal labels

Labels, nameplates and packaging

Signs and POS graphics

Labels, nameplates and packaging

Dials and clusters

Automotive

All applications →

Squeegee pressure, angle and hardness

Guide

Off-contact and snap-off

Guide

Emulsion thickness (EOM)

Guide

All guides →

## From Sunstar Academy

Real footage and short lessons from Sunstar's own channel.

All videos →

**5 Common Screen Printing Problems & How to Fix Them!** Are you facing blurry prints, uneven ink coverage, pinholes, registration errors, or inconsistent print quality? Sunstar Academy · 5:50

**Why Your Ink Viscosity Is Costing You Quality & Money** Ink viscosity can affect much more than how easily ink flows. It can influence print consistency, opacity, adhesion, dot gain, and rejection rates. Sunstar Academy · 3:26

## Tell Sunstar what you print.

An engineer replies within one working day with machine options and Indian pricing.

## About Sunstar Graphics

- Company: Sunstar Graphics Pvt. Ltd., an Indian distributor of industrial screen printing machinery
- Since: 1980, founded as Sunglo India by Ajit Lalvani; Sunstar Graphics formed in 2000
- Brands: Authorised distributor in India for ATMA (Taiwan), SPS and RKS (Germany), Grünig and SignTronic (Switzerland) and Lingtie and Luen Cheong (China). It also supplies Kuroki squeegees (Taiwan).
- Supplies: printers (flatbed, stop-cylinder, roll-to-roll, glass, PCB and part printers); pre-press and screen making (stretching, coating, computer-to-screen, washing); dryers and curing (IR, hot air and UV); feeders, stackers and converting; squeegees and tools
- Services: Consultation, supply, installation, operator training, service, spares and AMC
- Area served: All of India, from the office in Worli, Mumbai
- Address: Unit B-305, Neelam Centre, S K Ahire Marg, Worli, Mumbai, Maharashtra 400030, India
- Phone: +91 98203 61705
- Email: Sales@sunstargraphics.com
- Prices: Quoted in Indian rupees for each job; not published as a list
