---
title: Registration Problems in Multicolour Screen Printing: Fixes
url: https://www.sunstargraphics.com/guides/registration-problems-multicolour-screen-printing/
description: Registration problems in multicolour screen printing: how to read the error, fix shrinkage and screen tension, and CCD registration machines in India.
last_updated: 2026-11-17
---

# Registration problem in multicolour screen printing: causes and fixes

Registration problems in multicolour screen printing come from four places: the screens, the substrate, the press and the artwork. Look at how the error behaves before changing anything. A constant error is a setup fault. A random error is a feeding fault. An error that grows across the sheet is a change of size in the screen or the substrate.

## Read the error first

Print register marks in all four corners on every colour. Measure the error on ten sheets in a row and note its direction.

| What you see | Likely cause | Fix |
|---|---|---|
| Same shift on every sheet | Screen or image is in the wrong position | Move the screen with the micro-adjusters. Image all screens in the same position |
| Shift changes from sheet to sheet | Sheet not seated against the lays, weak vacuum, cut edges vary | Check lay stops and vacuum. Feed the same two edges for every colour |
| Fits on one side, off on the other | Substrate shrank in the dryer, or screens differ in tension | Pre-shrink the material. Match tension across the screen set |
| Error only along the print direction | Too much off-contact or squeegee pressure stretches the mesh | Lower both. Use the same values for every colour |
| Error grows during the run | Screen losing tension, or room temperature and humidity changing | Measure tension. Control the print room climate |

## Substrate shrinkage

Polycarbonate and polyester films shrink when they pass through a dryer. If the first colour is printed on fresh material and the sheet then shrinks, later colours will not fit. Common practice is to pass the blank sheets through the dryer once before printing, at the temperature used in production, or to buy heat-stabilised film. Keep the dryer temperature and belt speed the same for each colour.

Let material reach print room temperature before use. Paper and board change size with humidity, so keep the room steady.

## Screens and artwork

- Use the same mesh and frame size for every colour in the set.
- Keep tension within about 2 N/cm across the set.
- Stretch all screens with the mesh running in the same direction.
- Place the image in the same position on every screen.
- Film positives change size with heat and humidity. Computer-to-screen (CTS) imaging writes each screen from the file, in the same position.

## Press settings

Use three-point lay: two stops on the long edge and one on the short edge. Use the same edges for every colour and for die-cutting. Check lay stops for wear and screen clamps for play. Set off-contact equal at all four corners. On a hand-fed semi-automatic press, register depends on the operator seating each sheet the same way.

Check the fit of the first few sheets of each colour under a magnifier before running the batch, and check again at regular intervals during the run.

## Machines Sunstar supplies for tight register

Where the material itself moves, a camera system is the practical fix. A CCD registration screen printing machine reads printed marks on each sheet or repeat and aligns before it prints. Sunstar Graphics supplies the SPS ASTRON QX stop-cylinder press, with dual-camera registration to 30 microns, and the Lingtie LTA-5070, a CCD-registered screen printer with UV curing. ATMA flatbed printers have a repeat accuracy of ±0.02 mm. SignTronic CTS imaging and Grünig stretching machines deal with the screen side.

Send an enquiry with your material, sheet size, number of colours and tolerance for machine options and Indian pricing.

## Machines for this

Supplied in India by Sunstar.

- [**SPS ASTRON QX 57**](https://www.sunstargraphics.com/machines/sps-astron-qx-57/): The newest generation of STOP cylinder screen printing machines is the SPS ASTRON QX range: an automatic 4-post press that is fully servo driven, with CCD camera image registration to an accuracy of 30 um or better.
- [**Lingtie LTA-5070**](https://www.sunstargraphics.com/machines/lingtie-lta-5070/): Automatic screen printing machine with CCD optical vision alignment system can effectively improve the printing accuracy, improve the accurate identification of the printing image, avoid the printing results of movement, deflection, blurred edge.

- [**ATMA AT-80P/SV**](https://www.sunstargraphics.com/machines/atma-at-80p-sv/): Electric Flat Screen Printer is suitable for printing Membrane Switch, Flexible PCB, Nameplate & Cards, etcindustrial products.
- [**SignTronic STM-ONE**](https://www.sunstargraphics.com/machines/signtronic-stm-one/): Compact CtS system for small to medium stencil volumes with an attractive entry price.

## Short answers

**Why do colours go out of register in screen printing?**

The usual causes are substrate shrinkage in the dryer, screens at different tensions, too much off-contact and sheets not seated against the lay stops. Measure the error on several sheets to see which one it is.

**How do I stop polycarbonate shrinking between colours?**

Pass the blank sheets through the dryer before the first colour, at production temperature, and keep the same dryer settings for every colour.

**What registration accuracy can a screen printing machine hold?**

It depends on the machine and the material. ATMA flatbeds have a repeat accuracy of ±0.02 mm, and the SPS ASTRON QX registers by camera to 30 microns.

**What is CCD registration in screen printing?**

Cameras read register marks on the sheet or web, and the machine aligns to them before each print. This corrects for material that has changed size or position.

### Ask an engineer

Tell Sunstar what you print. An engineer replies within one working day with machine options and Indian pricing.

CCD registration screen printing machines

10 models

Stop-cylinder screen printing presses

4 models

Flatbed screen printing machines

19 models

Dials and clusters

Automotive

IMD / in-mould decoration

Automotive

Membrane switches and overlays

Electronics

Flexible circuits (FPC)

Electronics

All applications →

Screen tension in N/cm

Guide

Off-contact and snap-off

Guide

CTS vs film positives

Guide

All guides →

## From Sunstar Academy

Real footage and short lessons from Sunstar's own channel.

All videos →

### 5 Common Screen Printing Problems & How to Fix Them!

Are you facing blurry prints, uneven ink coverage, pinholes, registration errors, or inconsistent print quality?

## Tell Sunstar what you print.

An engineer replies within one working day with machine options and Indian pricing.

## About Sunstar Graphics

- Company: Sunstar Graphics Pvt. Ltd., an Indian distributor of industrial screen printing machinery
- Since: 1980, founded as Sunglo India by Ajit Lalvani; Sunstar Graphics formed in 2000
- Brands: Authorised distributor in India for ATMA (Taiwan), SPS and RKS (Germany), Grünig and SignTronic (Switzerland) and Lingtie and Luen Cheong (China). It also supplies Kuroki squeegees (Taiwan).
- Supplies: printers (flatbed, stop-cylinder, roll-to-roll, glass, PCB and part printers); pre-press and screen making (stretching, coating, computer-to-screen, washing); dryers and curing (IR, hot air and UV); feeders, stackers and converting; squeegees and tools
- Services: Consultation, supply, installation, operator training, service, spares and AMC
- Area served: All of India, from the office in Worli, Mumbai
- Address: Unit B-305, Neelam Centre, S K Ahire Marg, Worli, Mumbai, Maharashtra 400030, India
- Phone: +91 98203 61705
- Email: Sales@sunstargraphics.com
- Prices: Quoted in Indian rupees for each job; not published as a list
