---
title: Off-Contact Distance and Snap-Off in Screen Printing Explained
url: https://www.sunstargraphics.com/guides/off-contact-snap-off-screen-printing/
description: Off-contact distance (snap-off) in screen printing: typical gaps by frame size, how to set it, and fixes for sticking screens. From Sunstar Graphics, India.
last_updated: 2026-11-17
---

# Off-contact distance (snap-off) in screen printing: how to set it

Off-contact distance, also called snap-off, is the gap between the underside of the screen and the substrate before the squeegee presses the mesh down. On a well-tensioned screen it is typically 1 to 3 mm for small frames and 3 to 8 mm for large frames. Use the smallest gap that lets the mesh lift cleanly behind the squeegee.

## What off-contact does

In off-contact printing the mesh touches the substrate only along the line of the squeegee. Behind the blade the mesh springs back up and leaves the ink on the sheet. This lift is the snap-off. A clean snap-off gives sharp edges and an even ink film.

If the screen stays stuck to the wet print, the ink is disturbed when the frame lifts. If the gap is too large, the squeegee has to push the mesh a long way down, and the image stretches with it.

## Typical off-contact distance

The right gap depends on screen tension, frame size, ink tack and print speed. A tight screen needs less gap than a slack one. The figures below are typical starting points. Thick, tacky inks and fast strokes need a little more, so check the ink maker's data sheet if it gives a print gap.

| Screen | Typical off-contact |
|---|---|
| Small frame, high tension, fine functional work | 0.5 to 2 mm |
| Frame up to about 600 × 800 mm | 2 to 4 mm |
| Frame of about 1000 × 1500 mm | 4 to 8 mm |
| Very large glass and signage frames | 8 mm or more |

## How to set the gap

Some presses also lift the back of the frame as the squeegee travels. This is called peel-off, and it helps the mesh release with a smaller gap.

- Measure screen tension first. A slack screen cannot be corrected with off-contact.
- Set the gap equal at all four corners with gauge blocks or feeler gauges, measured to the surface of the substrate.
- Start low and raise the gap in small steps until the mesh lifts directly behind the squeegee along the whole stroke.
- Leave free mesh between the image and the frame on all sides, so the squeegee does not have to force the mesh down close to the frame.
- Record the gap with the job so the next run starts from the same setting.

## Problems caused by the wrong gap

| Problem | Likely cause | Fix |
|---|---|---|
| Screen sticks to the print, solids look smeared or mottled | Gap too small, low screen tension or tacky ink | Raise the gap in small steps, check tension, slow the stroke |
| Image prints longer than the artwork, colours out of register | Gap too large, so the mesh stretches | Lower the gap and use the same gap for every colour |
| Weak print near the frame | Image too close to the frame | Use a larger frame or lower the gap |
| Stencil or mesh wears out early | A high gap needs high squeegee pressure | Lower the gap and the pressure together |
| Sharp on one side, smeared on the other | Gap unequal across the frame | Reset all four corners to the same value |

## Machines Sunstar supplies that hold off-contact steady

A steady off-contact needs a frame that lifts parallel to the bed and returns to the same height on every cycle. ATMA flatbed screen printers, which Sunstar Graphics supplies in India, use a motor-driven vertical screen lift and a servo print stroke, with a repeat accuracy of ±0.02 mm. The AT-80P/SV and AT-120P are electric flatbeds. The ATMACE 67/G(6) is a fully automatic flatbed with a feeder.

Off-contact also depends on screen tension, which is set on a Grünig stretching machine. Send an enquiry with your sheet size and material for machine options and Indian pricing.

## Machines for this

Supplied in India by Sunstar.

- [**ATMA AT-80P/SV**](https://www.sunstargraphics.com/machines/atma-at-80p-sv/): Electric Flat Screen Printer is suitable for printing Membrane Switch, Flexible PCB, Nameplate & Cards, etcindustrial products.
- [**ATMA AT-120P**](https://www.sunstargraphics.com/machines/atma-at-120p/): Electric flat screen printer is suitable for screen printing on flexible or rigid material flat sheet such as Membrane Switch, Flexible Printer Circuits, Nameplate, Electro-luminescent, etcindustrial products.

- [**ATMA ATMACE 67/G(6)**](https://www.sunstargraphics.com/machines/atma-atmace-67-g-6/): Suitable for graphic or industrial printing onto rigid and flexible material flat substrate such as ceramic transfer paper, advertisement sticker or decal, package case for cigarette and liquor, UV varnish, membrane switch, automotive dashboard, etc.
- [**Grünig G-STRETCH 281**](https://www.sunstargraphics.com/machines/grunig-g-stretch-281/): The G-STRETCH 281 BASIC enables you to reduce mesh costs, to stretch with utmost speed and flexibility while keeping expenses under control.

## Short answers

**What is off-contact distance in screen printing?**

It is the gap between the bottom of the screen and the substrate before printing. The squeegee pushes the mesh down across this gap, and the mesh lifts again behind the blade.

**What is the difference between off-contact and snap-off?**

Most factories use both words for the same setting. Off-contact is the gap, and snap-off is the mesh lifting from the print behind the squeegee.

**How much off-contact should I use?**

Typically 2 to 4 mm on a medium frame with good tension, and more on large frames. Use the smallest gap that gives a clean release.

**Why does my screen stick to the print?**

The gap is too small or the screen tension is too low for the ink. Check tension first, then raise the off-contact in small steps.

### Ask an engineer

Tell Sunstar what you print. An engineer replies within one working day with machine options and Indian pricing.

Flatbed screen printing machines

19 models

Semi-automatic screen printing machines

17 models

Screen stretching machines

5 models

Membrane switches and overlays

Electronics

Nameplates and metal labels

Labels, nameplates and packaging

Dials and clusters

Automotive

All applications →

Screen tension in N/cm

Guide

Squeegee pressure, angle and hardness

Guide

Screen printing defects

Guide

All guides →

## Tell Sunstar what you print.

An engineer replies within one working day with machine options and Indian pricing.

## About Sunstar Graphics

- Company: Sunstar Graphics Pvt. Ltd., an Indian distributor of industrial screen printing machinery
- Since: 1980, founded as Sunglo India by Ajit Lalvani; Sunstar Graphics formed in 2000
- Brands: Authorised distributor in India for ATMA (Taiwan), SPS and RKS (Germany), Grünig and SignTronic (Switzerland) and Lingtie and Luen Cheong (China). It also supplies Kuroki squeegees (Taiwan).
- Supplies: printers (flatbed, stop-cylinder, roll-to-roll, glass, PCB and part printers); pre-press and screen making (stretching, coating, computer-to-screen, washing); dryers and curing (IR, hot air and UV); feeders, stackers and converting; squeegees and tools
- Services: Consultation, supply, installation, operator training, service, spares and AMC
- Area served: All of India, from the office in Worli, Mumbai
- Address: Unit B-305, Neelam Centre, S K Ahire Marg, Worli, Mumbai, Maharashtra 400030, India
- Phone: +91 98203 61705
- Email: Sales@sunstargraphics.com
- Prices: Quoted in Indian rupees for each job; not published as a list
