---
title: Mesh Count for Conductive Ink and Silver Paste Printing
url: https://www.sunstargraphics.com/guides/mesh-count-for-conductive-ink-silver-paste/
description: Mesh count for conductive ink, silver paste and carbon paste: typical polyester and stainless steel mesh, deposit and resistance. For factories in India.
last_updated: 2026-11-17
---

# Choosing the mesh count for conductive ink, silver paste and carbon paste

For silver and carbon conductive pastes on membrane switches and printed sensors, polyester mesh of about 61 to 90 threads per cm is typical. Finer tracks use polyester of 120 threads per cm or more, or stainless steel mesh of 325 to 400 threads per inch. Start with the mesh named in the paste maker's data sheet, because particle size and target resistance decide the choice.

## Typical mesh for conductive and dielectric inks

These are typical choices. Mesh makers write a mesh as count and thread diameter. For example, 77-48 means 77 threads per cm with a 48 micron thread.

| Layer | Typical mesh | Notes |
|---|---|---|
| Silver tracks, lines of 300 microns and wider | Polyester, 61 to 90 threads per cm | The common choice for membrane switch circuits |
| Carbon pads and resistors | Polyester, 61 to 90 threads per cm | Resistance follows film thickness closely |
| Fine silver lines, under about 150 microns | Stainless steel, 325 to 400 threads per inch, or fine polyester | Needs a thin, flat stencil |
| Dielectric and insulation ink | Polyester, 77 to 120 threads per cm | Often printed in two layers to close pinholes |
| Silver / silver chloride and biosensor carbon | As the paste data sheet states | Electrode area and thickness set the reading |

## What the mesh decides

Mesh count and thread diameter together set the theoretical ink volume, which mesh makers publish in cm³ per m². That volume sets the wet film. The wet film sets the dry film, and the dry film sets the resistance of the track. Two meshes with the same count and different thread diameters give different deposits.

A coarser mesh gives a thicker track with lower resistance and uses more silver. A finer mesh saves paste and prints narrower lines, with higher resistance. The mesh opening should also be at least about three times the largest particle in the paste, or flakes will block the mesh.

## Polyester or stainless steel mesh

Polyester mesh costs less, survives handling and suits most membrane switch and sensor work. Stainless steel mesh has thinner wires and a larger open area for the same count. It holds its size better and takes higher tension, so it suits fine lines and tight tolerances. It costs more, and a dent in it is permanent.

## Stencil, print and drying

- Keep the stencil thin and flat for fine lines. Thick emulsion adds deposit at the line edges.
- Stretch the mesh at an angle, commonly 22.5 degrees, so tracks do not run along the threads.
- Use an emulsion that resists the solvents in the paste.
- Hold squeegee speed and pressure constant. A change in either changes the resistance.
- Dry to the time and temperature in the paste data sheet. Under-dried silver reads high.
- Print a test track on every sheet and measure its resistance.

## Machines Sunstar supplies for conductive ink printing

The press has to lay down the same film on every sheet. ATMA flatbed screen printers, which Sunstar Graphics supplies in India, use a servo print stroke and a motor-driven vertical screen lift. The ATMACE 67/G(6) is a fully automatic flatbed with a feeder. For work on the reel, the Lingtie LTA-80200 is a fully automatic roll-to-roll (reel to reel) screen printer. Luen Cheong IR hot-air drying tunnels such as the LC-SD 7000 dry the paste in line, and the SignTronic STM MICRO images fine-line screens without film.

Send an enquiry with your paste, substrate and line width for machine options and Indian pricing.

## Machines for this

Supplied in India by Sunstar.

- [**ATMA ATMACE 67/G(6)**](https://www.sunstargraphics.com/machines/atma-atmace-67-g-6/): Suitable for graphic or industrial printing onto rigid and flexible material flat substrate such as ceramic transfer paper, advertisement sticker or decal, package case for cigarette and liquor, UV varnish, membrane switch, automotive dashboard, etc.
- [**Lingtie LTA-80200**](https://www.sunstargraphics.com/machines/lingtie-lta-80200/): This machine plays a critical role in the manufacturing process of solar cells by depositing conductive pastes onto the photovoltaic substrate, allowing for the efficient conversion of sunlight into electricity.

- [**Luen Cheong SD7000**](https://www.sunstargraphics.com/machines/luen-cheong-lc-sd-7000/): This conveyor dryer is widely used in the drying of screen printing industry, is especially suitable for solidifying heat-set and special type of printing ink.
- [**SignTronic STM-MICRO**](https://www.sunstargraphics.com/machines/signtronic-stm-micro/): Compact solution for small formats with optimized handling and high imaging quality.

## Short answers

**What mesh count is used for silver conductive ink?**

Polyester mesh of about 61 to 90 threads per cm is typical for membrane switch circuits. Check the paste maker's data sheet, which names a recommended mesh.

**Should I use stainless steel or polyester mesh for silver paste?**

Polyester suits most tracks of 300 microns and wider. Stainless steel suits fine lines and tight thickness tolerances, at a higher screen cost.

**How does mesh count affect resistance?**

A coarser mesh deposits a thicker film, which lowers resistance. A finer mesh deposits less paste, so resistance is higher.

**What mesh is used for carbon paste?**

Carbon pastes are commonly printed through polyester mesh of 61 to 90 threads per cm. The paste data sheet gives the mesh and the drying conditions.

### Ask an engineer

Tell Sunstar what you print. An engineer replies within one working day with machine options and Indian pricing.

Flatbed screen printing machines

19 models

Roll-to-roll screen printing machines

4 models

IR and hot-air conveyor dryers

8 models

Membrane switches and overlays

Electronics

Printed sensors and seat mats

Electronics

Glucose test strips

Medical and diagnostics

Flexible circuits (FPC)

Electronics

All applications →

How membrane switches are made

Guide

How glucose test strips are screen printed

Guide

Emulsion thickness (EOM)

Guide

All guides →

## From Sunstar Academy

Real footage and short lessons from Sunstar's own channel.

All videos →

### More Ink is not Better Print | The Truth About Ink Deposit

More ink doesn’t always mean a better print.

## Tell Sunstar what you print.

An engineer replies within one working day with machine options and Indian pricing.

## About Sunstar Graphics

- Company: Sunstar Graphics Pvt. Ltd., an Indian distributor of industrial screen printing machinery
- Since: 1980, founded as Sunglo India by Ajit Lalvani; Sunstar Graphics formed in 2000
- Brands: Authorised distributor in India for ATMA (Taiwan), SPS and RKS (Germany), Grünig and SignTronic (Switzerland) and Lingtie and Luen Cheong (China). It also supplies Kuroki squeegees (Taiwan).
- Supplies: printers (flatbed, stop-cylinder, roll-to-roll, glass, PCB and part printers); pre-press and screen making (stretching, coating, computer-to-screen, washing); dryers and curing (IR, hot air and UV); feeders, stackers and converting; squeegees and tools
- Services: Consultation, supply, installation, operator training, service, spares and AMC
- Area served: All of India, from the office in Worli, Mumbai
- Address: Unit B-305, Neelam Centre, S K Ahire Marg, Worli, Mumbai, Maharashtra 400030, India
- Phone: +91 98203 61705
- Email: Sales@sunstargraphics.com
- Prices: Quoted in Indian rupees for each job; not published as a list
