---
title: Fine Line Screen Printing on Polycarbonate: Settings Guide
url: https://www.sunstargraphics.com/guides/fine-line-screen-printing-polycarbonate/
description: Fine line screen printing on polycarbonate: mesh count, screen tension, stencil, squeegee and off-contact settings, with typical values, for plants in India.
last_updated: 2026-11-17
---

# How to print fine lines on polycarbonate by screen printing

Fine lines on polycarbonate need four things to be right together: a fine mesh at high tension, a thin and flat stencil with a sharp image, a sharp squeegee at low pressure, and a clean, flat sheet free of static. Lines of around 100 to 150 microns are typically achievable on a well set flatbed press. Finer lines need closer control of every step.

## Start with the screen

Most fine-line problems begin in the screen room.

- Mesh. Use a high mesh count with a thin thread, typically 120 to 165 threads per cm for graphic inks. The mesh opening has to be large enough for the ink to pass. A common rule is an opening at least three times the largest particle in the ink. Check the ink maker's data sheet for the recommended mesh
- Tension. Stretch to the tension the mesh maker recommends, typically 18 to 25 N/cm for fine polyester mesh, and keep it even across the frame. Low or uneven tension lets the image stretch and the lines blur
- Mesh angle. Mesh is often stretched at an angle to the frame, commonly 22.5 degrees, so that the threads do not run along straight lines in the artwork. This reduces sawtooth edges
- Stencil. Coat a thin, flat stencil. Emulsion over mesh (EOM) is typically a few microns for fine lines. A thick stencil prints a tall line that spreads. A rough stencil lets ink creep under the edge
- Image. Expose from a sharp, dense film positive in good vacuum contact, or image the screen by computer-to-screen (CTS). CTS writes the artwork straight onto the emulsion, so there is no film to distort or lose contact

## Press settings for fine lines

| Setting | Typical for fine lines | Reason |
|---|---|---|
| Off-contact (snap-off) | As low as still peels cleanly, typically 2 to 4 mm on a mid-size frame | High off-contact stretches the image |
| Squeegee hardness | Typically 70 to 80 Shore A with a sharp edge | A soft or rounded edge pushes through too much ink |
| Squeegee angle | Typically 70 to 75 degrees | A more upright blade deposits less ink |
| Squeegee pressure | The lowest that prints the full image | Extra pressure spreads the line |
| Print speed | Moderate and constant | Gives the ink time to fill fine openings |
| Flood stroke | Light and even | A heavy flood pushes ink through before the print |

## Polycarbonate needs its own care

- Static and dust. Polycarbonate sheet picks up a static charge when the protective film is peeled off. The charge attracts dust and can make the ink spread in fine hairs. Use an ionising bar and a tacky roller, and keep the print room clean
- Ink. Some solvents attack polycarbonate and cause stress cracks. Use an ink made for polycarbonate and the thinner its maker recommends
- Flatness. Polycarbonate film for dials and overlays is typically 0.25 to 0.5 mm thick. A vacuum bed has to hold it flat across the whole print area
- Heat. The film can change size in the dryer. Keep the drying conditions the same for every pass so that later colours register, and check the film maker's data sheet

## Common faults and their causes

- Lines print wider than the artwork: too much pressure, a soft or rounded squeegee, a thick stencil or ink that is too thin
- Sawtooth edges: mesh too coarse, a rough stencil, or threads running along the line
- Broken lines: mesh too fine for the ink, ink drying in the mesh, too little pressure or dust on the sheet
- Lines out of position: low screen tension, high off-contact or a sheet that moves on the bed

## What Sunstar supplies

Sunstar Graphics supplies each part of a fine-line printing set-up in India. ATMA flatbed screen printers have a servo print stroke, a motor-driven vertical screen lift and a repeat accuracy of ±0.02 mm. The SignTronic STM MICRO is a computer-to-screen system for fine-line imaging. Grünig stretching and coating machines give a set tension and a repeatable emulsion thickness. RKS and Kuroki squeegees and ATMA squeegee sharpeners keep the blade edge sharp.

Sunstar is the exclusive distributor in India for these brands and installs, trains and services from Mumbai, across India. Send an enquiry with your line width, sheet size and ink. Sunstar replies within one working day, and you can ask for machine options and Indian pricing.

## Machines for this

Supplied in India by Sunstar.

- [**ATMA AT-80P/SV**](https://www.sunstargraphics.com/machines/atma-at-80p-sv/): Electric Flat Screen Printer is suitable for printing Membrane Switch, Flexible PCB, Nameplate & Cards, etcindustrial products.
- [**SignTronic STM-MICRO**](https://www.sunstargraphics.com/machines/signtronic-stm-micro/): Compact solution for small formats with optimized handling and high imaging quality.

- [**Grünig G-COAT 414**](https://www.sunstargraphics.com/machines/grunig-g-coat-414/): G-COAT 414 – the economical and flexible coating machine for screen sizes of up to 2 x 2 meters.
- [**RKS HT3**](https://www.sunstargraphics.com/machines/rks-ht3/): Three-layer polyurethane squeegee designed for the electronics industry, for printing polymer-like pastes and silver-containing print media.

## Short answers

**What is the finest line that can be screen printed on polycarbonate?**

Typically around 100 to 150 microns in production with graphic inks on a well set press. Finer lines are possible with finer mesh, a thin stencil and CTS imaging, and the limit depends on the ink.

**Which mesh count is used for fine line screen printing?**

Typically 120 to 165 threads per cm with a thin thread for graphic inks. Check the ink maker's data sheet, because the mesh opening has to suit the ink.

**Why do fine lines print with sawtooth edges?**

The stencil edge is following the mesh threads. A finer mesh, a flatter stencil and mesh stretched at an angle to the artwork reduce it.

**Does computer to screen help fine line printing?**

Yes. CTS images the screen direct from the file, so there is no film positive to distort or lose contact during exposure.

### Ask an engineer

Tell Sunstar what you print. An engineer replies within one working day with machine options and Indian pricing.

Flatbed screen printing machines

19 models

Computer-to-screen (CTS) machines

4 models

Screen stretching machines

5 models

Dials and clusters

Automotive

Membrane switches and overlays

Electronics

IMD / in-mould decoration

Automotive

Nameplates and metal labels

Labels, nameplates and packaging

All applications →

Screen tension in N/cm

Guide

Emulsion thickness (EOM)

Guide

Off-contact and snap-off

Guide

All guides →

## Tell Sunstar what you print.

An engineer replies within one working day with machine options and Indian pricing.

## About Sunstar Graphics

- Company: Sunstar Graphics Pvt. Ltd., an Indian distributor of industrial screen printing machinery
- Since: 1980, founded as Sunglo India by Ajit Lalvani; Sunstar Graphics formed in 2000
- Brands: Authorised distributor in India for ATMA (Taiwan), SPS and RKS (Germany), Grünig and SignTronic (Switzerland) and Lingtie and Luen Cheong (China). It also supplies Kuroki squeegees (Taiwan).
- Supplies: printers (flatbed, stop-cylinder, roll-to-roll, glass, PCB and part printers); pre-press and screen making (stretching, coating, computer-to-screen, washing); dryers and curing (IR, hot air and UV); feeders, stackers and converting; squeegees and tools
- Services: Consultation, supply, installation, operator training, service, spares and AMC
- Area served: All of India, from the office in Worli, Mumbai
- Address: Unit B-305, Neelam Centre, S K Ahire Marg, Worli, Mumbai, Maharashtra 400030, India
- Phone: +91 98203 61705
- Email: Sales@sunstargraphics.com
- Prices: Quoted in Indian rupees for each job; not published as a list
