---
title: Screen Printing Dryers: IR, Hot Air and UV | Sunstar Graphics
url: https://www.sunstargraphics.com/dryers/
description: Screen printing dryers in India from Sunstar Graphics: Luen Cheong IR hot-air conveyor dryers, UV curing machines and IR + UV ovens, with how drying works.
last_updated: 2026-11-17
---

# Dryers and UV curing machines for screen printing: how they work, how to choose

After the press the ink is wet. It has to be dried or cured before the sheet can be stacked, printed again or finished. Solvent and water-based inks dry when the liquid in them leaves; heat and moving air speed this up. Plastisol fuses with heat. UV ink does not dry at all; it cures in seconds when UV light of the right dose reaches it. The dryer has to match the ink, the material and the speed of the press in front of it.

See the range

Sunstar Graphics is the exclusive distributor in India for Luen Cheong conveyor dryers from Hong Kong: IR hot-air drying tunnels, UV drying machines and combined IR and UV ovens. This page explains how a conveyor dryer works, what to check before buying, and the three types in the range. Dryers are matched to a press, so send the press model with the enquiry.

## How it works

1. **Feed** The printed sheet goes from the press take-off onto the dryer belt, by hand, by conveyor or straight from a cylinder press. The belt width is matched to the sheet.
2. **Heat or irradiate** In an IR hot-air tunnel, infrared lamps heat the ink and the material while hot air moves across the surface and carries the solvent or water away. In a UV curing machine, UV lamps above the belt deliver a dose of UV energy, measured in mJ/cm2, that cures the ink film in seconds.
3. **Hold** The belt speed and the tunnel length set how long the sheet is under heat or light. A longer tunnel or a slower belt gives more time. The temperature or the UV dose is set for the ink; the ink maker's data sheet gives the figure.
4. **Extract** Solvent vapour and hot air are extracted from the tunnel and vented, which keeps the shop air clean and the drying even. UV units extract the ozone and heat from the lamps.
5. **Cool and stack** A cooling zone at the exit brings the sheet back to room temperature so it can be stacked or printed again without the sheets sticking or distorting. A stacker or operator takes the sheets off.

### Compare models

Put two or three machines side by side, specification by specification.

Open the comparison

### 68 models

Lingtie, Luen Cheong, SPS

All dryers in the catalogue

### Ask an engineer

Send your material, sheet size and volume. An engineer replies with the right type and model.

## See the machines work

Animated models of the machines in this category, one cycle each. Press play.

All films →

**How an IR tunnel dryer works** Printed sheets ride a belt through infrared heaters, then hot air carries the solvent away and a cooling zone brings the sheet back to room temperature. Animated model of this machine. Silent, 30 seconds. [Open the interactive 3D version](https://www.sunstargraphics.com/demos/luen/)

## How to choose

What to settle before asking for a quotation.

Buying guides →

### Ink type

Solvent and water-based inks need IR and hot air. Plastisol needs heat to fuse. UV ink needs a UV curing machine. Shops that run both need a combined IR and UV oven or two dryers. Check the ink data sheet for the drying temperature or the UV dose.

### Press speed and sheet size

The dryer must take sheets as fast as the press delivers them. Give the press output per hour and the largest sheet; the belt width and the tunnel length follow from these.

### Material

Thin films, PVC and some plastics distort at the temperatures that dry thick inks on board or metal. Say what you print so the heat and the cooling zone are sized for it.

### Space and services

A conveyor dryer is long: the LC-SD series runs from the 2000 to the 10000 and the length is part of the model name. Measure the floor, and check the power supply and the exhaust route.

### Running cost

Lamps, belts and extraction use power and need replacing. Ask about lamp life, belt material and how the temperature and UV dose are monitored on the machine.

## IR hot-air conveyor dryers

Infrared lamps and moving hot air dry solvent, water-based and plastisol inks on a belt, in tunnel lengths from the LC-SD 2000 to the LC-SD 10000.

All 34 models →

- [**Lingtie LTB-1500**](https://www.sunstargraphics.com/machines/lingtie-ltb-1500/): The industry automatic hot air dryer is an efficient drying solution used in food, chemical, and pharmaceutical industries.
- [**Lingtie LTB-350**](https://www.sunstargraphics.com/machines/lingtie-ltb-350/): Hot air drying machine is an important part of the screen printing process, it can be customized according to the actual needs of users of various specifications and functions of the oven (oven/drying box).

- [**Lingtie LTB-800**](https://www.sunstargraphics.com/machines/lingtie-ltb-800/): The area of machine is small, inner loop 12 laps, 80 meters in length, which can be drying in a low temperature, ensure printed material no shrinkage deformation, easy to multicolor printing.
- [**Lingtie LTCB-800**](https://www.sunstargraphics.com/machines/lingtie-ltcb-800/): Automatic Pre-shrinking machine: 1.

[All 34 models in the catalogue →](https://www.sunstargraphics.com/machines/?cat=dryers&q=ir)

## UV curing machines

UV lamps over a conveyor belt cure UV inks and coatings in seconds, from the TM-200 to the TM-1200.

All 30 models →

- [**Luen Cheong TM-800UVF**](https://www.sunstargraphics.com/machines/luen-cheong-tm-800-uv-f/): Our latest innovation, the TM-800UVF UV Curing Machine, is engineered for performance in a wide range of industrial applications.
- [**Lingtie LTA-UV**](https://www.sunstargraphics.com/machines/lingtie-lta-uv/): The LED UV Dryer system is customized for all the printing industry demand.

- [**Lingtie LTB-600**](https://www.sunstargraphics.com/machines/lingtie-ltb-600/): The temperature of the Unique Pre-shrink Curing Oven can reach 200 Celsius and can be built with options for special requests.
- [**Lingtie LTUV-500**](https://www.sunstargraphics.com/machines/lingtie-ltuv-500/): UV energy "cures" inks and varnishes in a fraction of a second.

[All 30 models in the catalogue →](https://www.sunstargraphics.com/machines/?cat=dryers&q=uv)

## Combined IR + UV ovens

One tunnel with IR hot-air and UV sections, for shops that run both ink types or need to warm the ink before curing.

- [**Luen Cheong SD+TM-1100UVF**](https://www.sunstargraphics.com/machines/luen-cheong-sd-tm-1100uvf/): This integrated IR drying tunnel and UV curing machine offers a comprehensive solution for flat product finishing.
- [**Luen Cheong SD-UV8000**](https://www.sunstargraphics.com/machines/luen-cheong-uv-8000/): An integrated solution combining Infrared (IR) drying and Ultraviolet (UV) curing for efficient post-printing and coating processes.

- [**SPS TURBOSTAR CBS57**](https://www.sunstargraphics.com/machines/sps-turbostar-cbs57/): The screen printing combination dryer series CBS is a complete new modular design based on high volume jet-air technology together with energy saving UV systems.
- [**SPS TURBOSTAR CBS71**](https://www.sunstargraphics.com/machines/sps-turbostar-cbs71/): The screen printing combination dryer series CBS is a complete new modular design based on high volume jet-air technology together with energy saving UV systems.

## Machine types in this category

Each page explains one class of machine and lists its models.

- [UV conveyor dryers that cure UV inks in seconds after the press](https://www.sunstargraphics.com/uv-curing-machine-screen-printing/): A UV curing machine for screen printing is a conveyor that carries the printed sheet under UV lamps.
- [Infrared hot-air tunnels for solvent, water-based and conductive inks](https://www.sunstargraphics.com/ir-hot-air-conveyor-dryer/): An IR hot-air conveyor dryer carries the printed sheet on a belt through a heated tunnel.

## Guides

Written for the person choosing the machine.

All guides →

- [How membrane switches are made](https://www.sunstargraphics.com/guides/how-membrane-switches-are-made/): A membrane switch is made by screen printing a graphic overlay and one or two circuit layers on plastic film, then cutting them and laminating them with a spacer and adhesive. The circuit is printed in silver and carbon ink, with a dielectric layer for insulation. Each printed layer is dried or cured before the next, and each has to register to the others.
- [UV ink not curing](https://www.sunstargraphics.com/guides/uv-ink-not-curing-uv-dose/): UV ink that stays tacky, scratches off or fails a tape test has usually received too little UV energy for its film thickness and colour. Measure the UV dose on the belt with a radiometer, in mJ/cm², and compare it with the figure in the ink maker's data sheet. The common causes are an aged lamp, dirty reflectors, a belt running too fast and an ink film that is too thick.

- [Mesh count for conductive ink](https://www.sunstargraphics.com/guides/mesh-count-for-conductive-ink-silver-paste/): For silver and carbon conductive pastes on membrane switches and printed sensors, polyester mesh of about 61 to 90 threads per cm is typical. Finer tracks use polyester of 120 threads per cm or more, or stainless steel mesh of 325 to 400 threads per inch. Start with the mesh named in the paste maker's data sheet, because particle size and target resistance decide the choice.

Other categories: [Printers](https://www.sunstargraphics.com/printers/), [Pre-press and screen making](https://www.sunstargraphics.com/pre-press/), [Feeders, stackers and converting](https://www.sunstargraphics.com/handling/), [Squeegees and tools](https://www.sunstargraphics.com/squeegees/). See the [process stage by stage](https://www.sunstargraphics.com/process/) or [start from what you print](https://www.sunstargraphics.com/applications/).

## From Sunstar Academy

Real footage and short lessons from Sunstar's own channel.

All videos →

**SPS VITESSA XP57 primeline | Inline Drying Technology** Printing the sheet is only half the job. What happens after the print can determine how quickly the finished sheet is ready to handle, pack, and use. Sunstar Academy · 1:40

**VITESSA XP57: Print. Dry. Stack.** Printing is only half the process. The SPS VITESSA XP57 primeline takes production further with an inline drying workflowmoving sheets continuously from printing to… Sunstar Academy · 3:04

## Questions buyers ask

**Which dryer is used for screen printing?**

A conveyor dryer: an IR hot-air tunnel for solvent, water-based and plastisol inks, or a UV curing machine for UV inks. The choice depends on the ink and the press speed.

**What is the difference between IR dryer and UV dryer?**

An IR dryer removes the solvent or water from the ink with heat and air, which takes minutes. A UV dryer cures UV ink with ultraviolet light in seconds, with little heat on the material.

**Why is my UV ink not curing?**

Usually the UV dose is too low: the belt is too fast, the lamp is old, or the ink film is too thick for the dose. Check the dose in mJ/cm2 against the ink data sheet and the lamp hours.

**What size of conveyor dryer do I need?**

Match the belt width to your largest sheet and the tunnel length to the press speed and the ink drying time. Send the press model and ink type and Sunstar will size the dryer.

## Tell Sunstar what you print.

An engineer replies within one working day with the right type and model, and Indian pricing. Delivered and installed anywhere in India.

## About Sunstar Graphics

- Company: Sunstar Graphics Pvt. Ltd., an Indian distributor of industrial screen printing machinery
- Since: 1980, founded as Sunglo India by Ajit Lalvani; Sunstar Graphics formed in 2000
- Brands: Authorised distributor in India for ATMA (Taiwan), SPS and RKS (Germany), Grünig and SignTronic (Switzerland) and Lingtie and Luen Cheong (China). It also supplies Kuroki squeegees (Taiwan).
- Supplies: printers (flatbed, stop-cylinder, roll-to-roll, glass, PCB and part printers); pre-press and screen making (stretching, coating, computer-to-screen, washing); dryers and curing (IR, hot air and UV); feeders, stackers and converting; squeegees and tools
- Services: Consultation, supply, installation, operator training, service, spares and AMC
- Area served: All of India, from the office in Worli, Mumbai
- Address: Unit B-305, Neelam Centre, S K Ahire Marg, Worli, Mumbai, Maharashtra 400030, India
- Phone: +91 98203 61705
- Email: Sales@sunstargraphics.com
- Prices: Quoted in Indian rupees for each job; not published as a list
